2016 Dodge Challenger on 2040-cars

Auto blog

2018 Dodge Challenger SRT Demon First Drive | Don’t fear the Demon

"If you're not hurt, we'll be really pissed. If you are hurt, we'll still be pissed, but not quite as pissed." These are the words from Jim Wilder, the vehicle development manager of the 2018 Dodge Challenger SRT Demon, that echo through our head as we slide behind the wheel of the car for the first time. He was warning us about driving beyond our abilities, and keeping the car out of the wall. With 840 horsepower and 770 pound-feet of torque on tap from its supercharged, 6.7-liter V8, the Demon does 0-60 miles per hour in 2.3 seconds, and 0-30 mph in a second flat. If something does go wrong, it'll happen quickly. Following that talk, we had our guts sloshed as a passenger in a blurry eighth-mile run, giving us a taste of the G forces (the Demon can pull 1.8 G in a straight line) we'd feel when we got in the driver's seat for our own pass down the drag strip. We're already sweating. It had rained - you could describe it as torrential - the day before. The grassy parking areas surrounding Lucas Oil Raceway were still flooded, but any water on the pavement had evaporated and hung in the air. Combined with the heat, we were sticky and uncomfortable. In Drag Mode, the Dodge Demon's air conditioning turns off. Any condensation that it could leave on the track would be a problem, plus we need to reduce parasitic power losses for a faster run. The system is still working, though, the refrigerant diverted to the chiller system cooling the air coming into the engine. There's still condensation, but the Demon collects it on a catch pad to keep it from ending up on the pavement. We're also required to roll the windows up when entering the drag strip. For one thing, it helps keep the smoke out of the cabin during the pre-staging burnout. So, yeah, it's hot as Hell in the Demon. We pull through the water box and run through the sequence – which involves holding the "OK" button on the steering wheel usually used to navigate menus, and applying a specific amount of brake pressure before getting on the throttle to initiate the burnout. This gets any crud off the rear tires and heats up the rubber. There are multiple ways to launch the Demon. We had an instructor sitting in the passenger seat as we pulled up to the beams that trigger the Christmas tree at Lucas Oil Raceway. He walks us through the most complicated of the three he had explained to us just minutes before when we were in the passenger seat.

Dodge idles Viper production again at Conner Avenue

You've got to hand it to Dodge for having the gumption to put the original Viper into production in the first place. It was, after all, much more of an emotional decision than a practical one, and a move which saw the first production V10 engine placed in a road car - long before the advent of the Lamborghini Gallardo, Audi R8, Porsche Carrera GT or Lexus LFA, not to mention the other Ford, BMW and Volkswagen Group models that used such engines.
It's now been 22 years since the first Viper entered production and the Viper still rolls on several generations later, but we're sad to say that courageous decision has not always been met with overwhelming sales success. In fact parent Chrysler was forced to idle the Conner Avenue plant where the Viper is made back in April due to slow sales. And while production resumed again as planned on June 23, it apparently didn't do the trick.
As a result, Chrysler corporate communications chief Shawn Morgan revealed to Autoblog that the assembly line has been shut down again for another two weeks. The line was up and running for nearly two full work weeks from June 23 until the holiday weekend that started on Thursday, July 3. But instead of coming back online today as planned, it's been idled again for the weeks of July 7 and 14. That means it will be July 21, at the earliest, before the serpentine supercars start slithering down the assembly line at Conner Avenue again. Once it does, however, production is set to resume at the same pace it was before the shutdown.

2019 Dodge Charger SRT Hellcat Octane Edition fuels your dreams for a limited time

Few automakers love special-edition models quite as much as FCA. It's particularly prevalent in the Jeep and Ram lineups, but other makes get some love, too. Take a look at the new 2019 Dodge Charger SRT Hellcat Octane Edition, a special blacked-out model that's set to arrive at dealerships this fall. The car is available to order now, but Dodge says the books will only be open for a limited amount of time. The Octane Edition is available in two appropriately named colors: Pitch Black and White Knuckle. A pair of matte black stripes run down the middle of the car, flanked on both sides by a thin Octane Red stripe. The 20-inch wheels are painted gloss black and have a knurled bead to keep the tire from slipping on the rim. The Brembo brake package is included, with the six-piston front and four-piston rear calipers painted Octane Red to match the stripes. Inside, the Octane Edition gets houndstooth inserts in the SRT sport seats. There are red Hellcat logos, red seat belts and red stitching on the doors, seats, dash center console and steering wheel. The Octane Package adds $1,495 to the $68,740 base MSRP of a 2019 Charger Hellcat. Like all Hellcat models, the Charger comes with a supercharged 6.2-liter Hemi V8 making 707 horsepower and 650 pound-feet of torque. Power is sent to the rear wheels through an eight-speed automatic. Changes for '19 include a new grille with two inlets to feed more air under the hood. The cars also get launch control, line lock, a cooler for the supercharger as well as a torque reserve system that preloads the supercharger for better launches.