2009 Challenger R/t 5.7l V8 16v Automatic Rwd Coupe Cd Keyless Entry on 2040-cars

Auto blog

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

Junkyard Gem: 1976 Dodge D100, United States Army Edition

Members of the United States military have been driving Dodge trucks since the Army bought its first Dodge Brothers ambulance in 1917, and plenty of third-generation D-series pickups ended up in Army service during the mid-1970s. Most of these were 3/4-ton W200s and D200s (designated as M880s), but today's Junkyard Gem is a 1/2-ton D100 CARGO PICKUP W/CAB, found in a Denver self-service wrecking yard. Eventually, the Army auctions off old vehicles, and that happened to this battered D100 Custom at some point. This truck appears to have started life with Navy gray paint, which was painted over in Army-grade olive drab. Perhaps there was some vehicle-shuffling done by the Pentagon. The most recent layer of stickers shows that this truck's final military job was for the U.S. Army Recruiting Command. Power came from the legendary Chrysler Slant-6, in this case the 225-cubic-inch version rated at 105 horsepower. Like most fleet vehicles of the last 50 or so years, it has an automatic transmission. You couldn't expect every soldier to be able to work a three-pedal truck, not even way back in 1976. The Rust Monster has taken a few bites out of this truck, enough that its resale value converged with the current price of scrap vehicles. This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Better price, mileage and payload than Ford or Chevy!

FCA recalls 210,000 new Jeeps and Dodges due to a brake issue

FCA is recalling some 210,000 vehicles in the U.S. and elsewhere over a possible braking issue. On this occasion, the recall is made less complicated by the fact that about one-third of the affected vehicles are so new, they still reside on dealer lots, making them easy to tally up and put right. The recall concerns 2018 Dodge Journeys, 2019 Jeep Cherokees and 2018-2019 Dodge Grand Caravans and 2018-2019 Jeep Compasses. Most were built in spring 2018, and the recall is related to a brake system component that failed to meet FCA specifications. Further information available on the NHTSA website details the issue, saying that insufficiently coated rear brake caliper pistons may cause gas pockets to form in the brake fluid of very new vehicles. This in turn can reduce rear brake performance — bubbles in brake lines are not desirable. FCA underlines that the brakes still function, but stopping distance can be affected. As a remedy, the brake systems are inspected and re-bled. The recall is slated to begin on Sept. 28. In addition to 154,337 vehicles in the United States, the recall concerns 19,066 units in Canada, some 900 in Mexico and some 35,500 vehicles on other markets. Related Video: Image Credit: AOL Recalls Dodge Jeep Minivan/Van SUV FCA