Viper Gts, Tons Of Upgrades, Super Clean, Florida Car on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

The Fate of the Furious music video shows how much Demons love donuts

The new Dodge Demon is leaking into everything related to The Fate of the Furious in the lead-up to both the car and the film's debut in just over a month. The latest teaser involves Demons doing donuts and burnouts in the Get Off music video, with copious amounts of both tire smoke and hip hop to accompany the tire-shredding shenanigans. It also gives us a look at some of the film's other cars. Get Off is a song by Travis Scott, Quavo, and Lil Uzi that's featured on The Fate of the Furious soundtrack, which is out now. The teaser for the music video features a pack of Dodge Challengers - both Demon and non-Demon spec - along with a line of non-SRT related products. From what we can see, the movie will have a Scion FR-S/Toyota 86, a highly modified C2 generation Chevrolet Corvette, and a Mercedes-AMG GT S. In typical over-the-top fashion, the final shot shows a submarine bursting through ice in pursuit of several cars, including a Subaru WRX. We can't see much else as the full music video hasn't been released, but expect a few more teasers once it does. The Fate of the Furious debuts Friday, April 14, just days after the Dodge Demon's debut at the New York Auto Show. Related Video: News Source: Jetlag on Twitter TV/Movies Chevrolet Dodge Toyota music music video dodge hellcat the fate of the furious

Barracuda's Dodge branding no biggie, but what about engines?

Rumors about a revival of the Barracuda nameplate have been circulating for years now, though which brand it might fall under has been a bit of a mystery. Initial speculation had the car labeled an SRT product, but that acronym has since returned to its former role as a sub-brand for top-performance Mopars. Thanks to leaks from a recent FCA dealership event, we know the Barracuda is back on the table but will be sold under the Dodge umbrella, a move that has been generating a bit of ire from Pentastar fanatics, as the car was originally part of the defunct Plymouth brand. Given what's known about the new model, however, the badge is the least of my concerns about the new car. Let's start with the re-branding itself. This isn't the first time Chrysler has shuffled models around to different brands. The current-generation Viper spent two years as the flagship model under the SRT banner, only to return to Dodge for 2015 when SRT resumed its former role as a sub-brand. Years ago, the Neon was sold as a Plymouth, a Dodge, and a Chrysler model, depending on where you shopped for one. When Plymouth ceased to exist, the last few years of Prowler production got Chrysler badges instead. Then there's the new Jeep Renegade, a model whose name was born out of a trim level. The Barracuda might not turn out to be a muscle car in the way we currently define them. Further examples of naming liberties taken throughout automotive history could fill a book, but suffice it to say that these days a model's name has very little to do with the vehicle itself or any legacy it might have. The Barracuda name might be a particularly sacred cow with enthusiasts, but to me, a much bigger concern is the fact that the car might not turn out to be a muscle car in the way we currently define them. News from the Fiat Chrysler dealer briefing earlier this week indicates that when the next Charger debuts it will share its platform with the Barracuda, much the way the Charger and Challenger are twinned now. One difference is that the Barracuda is tipped to be offered as a convertible, while the modern Challenger is tintop-only. The Charger and Barracuda will use the rear-drive platform developed for Alfa Romeo's new Giulia, itself designed as a BMW M3 fighter both from a dimensional and dynamic standpoint; the Barracuda is expected to be slightly smaller than the current Challenger.