Limited Edition 2006 Viper Srt 10 Only 1935 Miles Video on 2040-cars

Auto blog

FCA recalls 894k total vehicles worldwide in two campaigns

FCA is recalling a total of 893,698 vehicles worldwide in two campaigns to fix problems with inadvertent airbag deployment, failure of the anti-lock brakes, and stability control systems in the Jeep Grand Cherokee, Liberty, Dodge Journey, and Fiat Freemont. 559,703 of these vehicles are in the US. The larger recall affects 284,089 examples of the 2003 Jeep Liberty and 2004 Jeep Grand Cherokee, and there are also 13,411 of them in Canada, 6,277 in Mexico, and 48,212 outside the NAFTA region. Because of "electrical noise beyond the tolerance of the airbag electronic control module", part of that component can fail, according to the National Highway Traffic Safety Administration. This can cause the front and side airbags to deploy and the seatbelt pre-tensioners to activate inadvertently. FCA US has seven reports of alleged injuries from this problem. To fix the situation, the Jeeps need their Occupant Restraint Control modules replaced, as well as the front- and side-impact sensors. According to the NHTSA, the replacement parts won't be available until early 2016. Still, FCA US will advise owners about the problem in a letter by the end of December and will send a second notification when the components are ready. The second campaign affects 275,614 examples of the 2012-2015 Dodge Journey in the US; plus 78,148 of them in Canada, 36,471 in Mexico, and 151,476 left-hand drive units outside of NAFTA where it's sold as the Fiat Freemont. On these vehicles, water intrusion can disable the anti-lock brakes and electronic stability control, although a warning light often illuminates when this issue occurs, and the problem doesn't affect regular braking. There are also no reports of injuries or accidents. To fix the issue, dealers will seal the ABS wiring harness and will replace any already affected components as necessary, like the ABS module or the headlamp and dashboard wiring harness. Statement: Occupant Restraint Control Modules October 30, 2015 , Auburn Hills, Mich. - FCA US LLC is voluntarily recalling an estimated 284,089 older-model SUVs in the U.S. to replace their Occupant Restraint Control (ORC) modules and front and/or side-impact sensors, as required. Within this vehicle population, FCA US became aware of seven injuries caused by inadvertent air-bag deployments and advised NHTSA accordingly. The affected vehicles are not equipped with Takata Corp. air-bags. The Company is unaware of any related accidents.

Speedkore AWD twin-turbo Carbon Charger, best birthday gift ever

The backstory the Speedkore Performance AWD twin-turbo Carbon Charger teased a couple of weeks ago might be cooler than the car itself. Alan Palermo commissioned the carbon-fiber-bodied Dodge Demon Speedkore brought to SEMA last year, the one that supplanted the 6.2-liter Hellcat V8's supercharger with twin 6875 Precision Billet T4 turbos. That blasted the Demon's usual 840 horsepower up to 1,400 hp at the flywheel, 1,203 hp at the rear tires, good for an 8.77-second quarter-mile time at 162 miles per hour. Palermo's older brother remarked, "He liked the car but was more of a four-door guy," so Alan commissioned the AWD Carbon Charger as a 65th birthday gift for his sibling. Speedkore worked with Magnaflow on the sedan, starting with a 2019 Charger Pursuit as a base. The Wisconsin tuner secured a 2020 widebody Charger from Dodge, then 3D-scanned the bodywork to create the molds reproducing most of the sheetmetal in pre-preg carbon fiber. The hood, bumpers, fenders, rockers, rear spoiler, and rear diffuser are all fashioned from the lightweight stuff.  Beyond those Precision turbos laid in by Gearhead Fabrications, Speedkore installed a custom upper plenum, Boost Leash C02 progressive boost controller, custom Thitek heads, a Fore Innovations triple-pump fuel system feeding Injector Dynamics 1,700-cc injectors, and custom HP Tuners engine software calibration. Test results showed 1,525 hp at the crank when running 26 pounds of boost.  Hellraiser Performance engineered a new transmission working an FTI torque converter at one end and a carbon fiber driveshaft at the other. Instead of fortifying an off-the-shelf AWD system, Traction Products supplied a custom transfer case machined from billet shunting power to a set of Bogart Competition Series wheels wearing Mickey Thompson ET street rubber.  Speedkore fitted last year's Demon with a front-exit twin exhaust, with a single opening on each front fender, and left the rear bumper cutouts for the traditional exhaust empty. With the Carbon Charger sedan more of a family guy, Magnaflow sorted out a quad-pipe front-exit exhaust with two openings on each front fender, and ran a three-inch stainless steel Competition Series exhaust to the rear. The driver can switch between the two, the latter version providing a "moderate interior sound."  The folks at Speedkore say they'll keep tweaking the Carbon Charger after the show to get it right for the senior Palermo. We say, "Happy birthday, sir. Enjoy."

How to tune a car right: Part 3, tuning Mopar with OST Dyno

Not long ago, I wrote a story about a pony car tuned with a supercharger. The blower install had been done properly. Then the car's owner bolted on a set of great looking wheels wrapped in good looking but inexpensive rubber. On my first test drive, I couldn't get any of that supercharged sweetness to the ground. It was the perfect ride for parking in a Burger King parking lot on a Friday night. I tooled around on a Sunday drive, shaking my head that someone had spent five figures to get more power the right way, with a clean install, then wiped out the gains so thoroughly that the stock engine would likely have overwhelmed the tires. This got me thinking about the ways people ruin their quest for horsepower, either on the front end by not insisting on a clean install and paying the money for it, or on the back end with supplemental purchases like cheap tires or cheap gas. So I called three tuners, one focused on GM, one on Mopar, one on Ford, to find out what people should know about how to get the best power for their goals, and how to make sure they are able to use all that power. The first interview in this three-part series was with Blake Leonard at Top Speed Cincy in Cincinnati, Ohio, the second with Brandon Alsept at BA Motorsports in Milford, Ohio. This third and last interview is with Micah Doban at OST Dyno in Slippery Rock, Pennsylvania, a family business with more than 40 years of Mopar expertise specializing in Gen III Hemis, but tuning everything from land-speed cars and drag racers to Jeeps The interview has been edited for clarity and concision. Do people who come to OST generally know what they want? Probably 80% of the people who come in simply want more power with no particular ET goal [ET is a kind of bracket handicapped drag racing – ed.]. WhatÂ’s the best way to start a Mopar tune? The first thing is what people often skip, and that's to find a tuner or a shop. People will throw parts on their cars that the Internet said to, then go to a tuner who does things a different way, and [the tuner is] like ‘No we don't like to use these injectors, we don't like these parts.Â’ You have to find someone familiar with the parts that are on your car or that you're planning to put on your car. So having a goal and then finding a tuner who can help you with that goal is proper way to start. Exactly. And a lot of tuners have their own formula – and when I say tuner I mean someone that also does work to the cars.