Like New Gts Viper With Only 503 Miles! Original Msrp Over $135k! on 2040-cars

Auto blog

Dodge recalls 173 Chargers and Challengers for front wheels that don't fit correctly

Dodge is recalling 173 Challengers and Chargers because they’re equipped with an incompatible front wheel and brake package. All the vehicles are 2019 model year cars built between May 28 and September 25 this year, according to the official NHTSA documents. The wheels donÂ’t provide enough clearance from suspension and brake components, Dodge says. ThereÂ’s a chance that the tireÂ’s inner sidewall will make contact with the steering knuckle. When the tire hits the steering knuckle, it could end up damaging the tire, causing a “sudden loss of tire air pressure.” This, of course, is not what you want out of a tire. Predictably, FCA says this could result in a crash without prior warning. To fix the problem, your local Dodge dealer will be installing the wheels that shouldÂ’ve been equipped on the car in the first place. FCA continues: “Also, for customer satisfaction, replace the rear wheels to match the front wheels.” We were wondering if the rear wheels would come into play here, and it looks like Dodge wonÂ’t be leaving anyone out to dry with mismatched front and rear wheels. The wheels in question are described as “Mid Gloss Black Wheel.” Check your window sticker (or wait for the official mailing) to see if you have those wheels on your Charger or Challenger. Unfortunately, FCA doesnÂ’t detail which trims of Charger and Challenger are affected in its recall notice. The company also makes it clear that this recall is due to “an engineering release error” and not a wheel defect. This particular wheel and brake package shouldÂ’ve never been offered as an option from the factory. Look out for a notice in early December, as FCA says it will begin notifying owners around December 13 this year. As of now, there are no reported injuries or accidents due to the issue.

Watch these Dodge Demons explode on a Texas drag strip

The Dodge Challenger SRT Demon is extremely quick. It can hit 60 mph from a dead stop in less time than it takes to read this sentence thanks to its supercharged 6.2-liter V8. That engine makes up to 840 horsepower and 770 pound-feet of torque, depending on what octane is running through the fuel lines. That's a ton of power going solely to the rear wheels. So much so that Dodge developed a number of features and a new set of tires specifically for the car. In our time with the Demon, the car took abuse run after run on a drag strip without skipping a beat, but it seems some actual owners aren't quite so lucky. Just take a look at what happened to a few of these cars. You can see the whole car shake and jitter right as the whole rear explodes in front of the tree. It seems the initial shock from the launch — the most taxing bit of any drag run — is what kills the differentials. Catastrophic failure is rarely pretty, but it is neat to see the whole thing occur in slow motion. Three more cars — four stock and one modified in total — suffered similar fates. Not a great look for Dodge or SRT. According to The Drive, a private drag event in Texas drew a number of Demon owners all trying to beat NHRA NHRA Top Fuel racer Leah Pritchett's time in her personal Dodge Demon — 42 stock Demons attended along with five modified cars. While no one managed to match her 9.65-second quarter-mile run, a few owners did dip below 10 seconds. Now, there are a few of caveats we must address. First, with any modified car, you run the risk of breaking something, even with a car that's set up from stock specifically for drag strips. Even a set of tires like the Mickey Thompsons shown in the video above can have an effect on driveline components. Horsepower may be king, but it's torque that's the rear killer. All that torque sends a shock through the car. Adding even more with aftermarket parts increases the risk of something failing. The modified car was apparently pushing out about 1,000 horsepower. That said, four of the five vehicles were stock, so any extra power or torque should theoretically be a non-factor. The drag strip's surface was maintained by a company called Mass Traction. FCA used Mass Traction during the Demon's development, so that too should be a non-factor in the part's failure. It's unclear what exactly caused the failures, though The Drive reports that FCA officials are investigating the matter. Related Video: This content is hosted by a third party.

Fiat Chrysler halts European production as coronavirus hits demand

MILAN — Fiat Chrysler Automobiles (FCA) is halting production for two weeks at most of its European plants to help protect staff against the coronavirus pandemic and adjust to a slump in demand, the Italian-American carmaker said on Monday. Italy has been the European country worst hit by the crisis and the first to enforce a nationwide lockdown, which has now been replicated by Spain and, to a lesser extent, by France as the virus sweeps through the continent. With all non essential services closed, including car dealers, and people forced home except for strict working needs, many forecast a heavy fall in car sales in March. FCA — which according to analyst estimates produces around 25% of its vehicles in Europe — said the suspensions through March 27 would allow it "to effectively respond to the interruption in market demand by ensuring the optimization of supply." Ferrari, meanwhile, said it closed its two plants until March 27. Ferrari said it had so far ensured production continuity, and it already implemented all the health measures decided by the Italian government at the two sites, in hometown Maranello and in Modena. But it was "now experiencing the first serious supply chain issues, which no longer allow for continued production." Marco Opipari, an analyst at Fidentiis, said a few weeks of closures was not a big problem in an over-supplied European auto industry and lost production could be recovered later on. "The real problem is on the demand side, people are not buying cars now, and sales volumes are expected to be very bad in March, with a real impact on automakers' earnings," he said. FCA said in a statement that production for its FCA Italy and luxury Maserati units would stop for two weeks, extending a temporary closure period already planned for some Italian facilities. Affected plants are Melfi, Pomigliano, Cassino, Mirafiori, Grugliasco and Modena in Italy, Kragujevac in Serbia and Tychy in Poland. The FIOM union said FCA's decision was "necessary". The carmaker said the freeze would help it to resume activity promptly once market conditions allow it. "The group is working with its supply base and business partners to be ready to enable our manufacturing operations to deliver previously planned total levels of production despite the suspension when market demand returns," it said.