2006 Dodge Viper Srt-10 Convertible 2-door 8.3l on 2040-cars

Auto blog

Dodge Viper recall requires small-handed mechanics

It has been over a year since Chrysler first announced its recall of 3,660 2003-2004 Dodge Vipers because the airbag could suddenly deploy. The repairs are finally beginning, and it appears to be a nightmare for mechanics.
According to the automaker's filing with the National Highway Traffic Safety Administration, the airbag control module can fail, which causes the bag or the seatbelt pre-tensioner to deploy without warning. It took over a year to design the new parts, according to The New York Times. However, Chrysler finally has a new "jumper harness with an in-line diode filter circuit" ready to fix the problem.
The dilemma now moves to the mechanics who have to actually install the part. A 47-step guide from Chrysler explains that the procedure should take about two hours. It's not an easy job, though. Most of the dashboard has to be taken apart, and the instructions include this helpful bit of advice: "Installing the jumper harness and filter box into position is not an easy task. Patience, perseverance, and small hands are required." We wish the best of luck to them. The fix comes just in time for the Vipers to enjoy the summer sun.

2015 Dodge Challenger SRT Hellcat gets brace of new videos

Yesterday's big announcement focusing on the new Dodge Challenger SRT Hellcat had plenty of stuff going for it - information, pictures and the rabid enthusiasm that always accompanies such an eagerly anticipated reveal. What it was lacking, though, was a proliferation of videos of the new model.
Sure, yesterday's news came with one clip, but today, Dodge has come through with five videos. We've arranged them in what we think will be the most entertaining order, covering the powertrain, before moving on to exterior and interior design, then on to a full CGI dissection of the SRT Hellcat before capping things off with a piece on the non-supercharged Challenger SRT392.
Take a look below for all five videos, then head into Comments and let us know what you think.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat