We Finance! 3500 Turbo Diesel Refrigerated Box 1owner Only 58,000 Miles! on 2040-cars

Auto blog

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

Chrysler recalls 1.2 million Ram pickup trucks

Chrysler has announced that it will issue three separate recalls that will cover as many as 1.2 million Ram pickup trucks for "steering-system tie rods that may have been misaligned during assembly or steering-system service." The vast majority of these trucks were sold in the United States, though some trucks in Mexico, Canada or overseas will be called in, as well.
The largest of the three recalls covers an estimated 842,400 model-year 2003-2008 Ram 2500 and 3500 trucks. Two smaller campaigns will bring 294,000 model-year 2008-2012 Ram 2500 and 3500 pickups, chassis cabs and 2008 Ram 1500 4x4 Mega Cabs; plus 43,500 model-year 2008-2012 Ram 4500 and 5500 4x4 chassis cabs into the dealer to be checked and repaired if necessary.
This is a very large recall, and Chrysler says it is "casting the net wider than necessary to identify those vehicles that require repair." The automaker estimates that "as many as 726,000 may not need repair."

Chrysler almost smothered the Hellcat before it lived

Chrysler's 6.2-liter supercharged Hellcat V8 was an absolute sensation from the very moment it was announced, and honestly, how could it not have been? Packing 707 horsepower and 650 pound-feet of torque, its numbers immediately put every other production muscle car (and many supercars) to shame. Plus, we soon learned that would be wrapped in a package retailing for around $60,000 - a pittance compared to other vehicles offering similar grunt. However, the Hellcat almost never got the chance to rumble under the hood of the Challenger and Charger.
The Hellcat was initially proposed back in 2011, back when Fiat was deciding its future strategy for Chrysler Group, according to Automotive News. At the time, the company was just emerging from its bankruptcy doldrums, and an ultra-high-performance V8 wasn't exactly a must-have item. The program didn't move forward. However, SRT engineers kept fighting, according to AN, and four months later, they received the green light to pull the project off the shelf and continue developing the Hellcat. The muscle car world is certainly better for that decision.
The work of those engineers focused on taking Chrysler's standard 6.2-liter V8 and making it reliably handle all of the extra power from the supercharger. "It came down to micron levels of changes in the crank to be able to withstand the pressures of the engine," said Chris Cowland, director of advanced and SRT powertrain, to Automotive News. The changes amounted to switching out about 91 percent of the parts to make the Hellcat, including some quite minuscule alterations. For example, the washer holding the supercharger pulley is embedded with industrial diamonds to keep it from slipping.