3/4 Ton Dodge Conversion Van 2500 Raised Roof Dual Ac Captains Chairs (4) Bed on 2040-cars

Auto blog

Dodge Challenger Shakedown: '71 body, new guts

While Jeep has created a number of vintage-bodied custom vehicles with modern components, this year's SEMA show plays host to Dodge's take on the idea. The Shakedown concept began life as a 1971 Challenger and ditched almost everything in it, including the engine and chassis. What's left is a modern car with a retro look. The chassis was a particularly complicated part of the job, since the Challenger was originally a unibody car. However, Dodge chose to separate the Challenger's iconic body from its structural parts, and moved it onto a custom, one-off chassis from which the body can be removed as needed. The chassis also carries lowered suspension, Challenger Hellcat brakes, and a 6.4-liter 392 Hemi V8 connected to a six-speed manual transmission from the Viper. Dodge also installed the engine using the new Hemi engine swap kit from Mopar. With the shaker cold-air intake and custom exhaust, the Shakedown's powerplant makes 485 horsepower. View 13 Photos The body itself received plenty of tweaking as well. Dodge shaved off the drip rails, door handles, and turn signals for a cleaner look, and also fitted the grille, headlights, and taillights from a 2017 Challenger. The whole thing is finished in matte black paint with a "vibrating" stripe offset on the left side. The Shakedown also gets 20-inch Slingshot rear wheels and a pair of custom 19-inch versions for the front. On each fender is a bright red "392" decal that uses the same font as the labels on classic Mopars 360 cubic-inch V8s. Inside, the Shakedown gets the same radical upgrade as the chassis. Two Viper seats accompany a Viper steering wheel, and the rear seats are gone altogether. The Viper gearbox is shifted with a Challenger Hellcat gear knob, and carbon-fiber accents and leather adorn the wheel, door panels, instrument panel and center console. Related Video: Image Credit: FCA, Joel Stocksdale SEMA Show Dodge Coupe Concept Cars Performance

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

Dodge Durango Shaker concept: A 392 V8 in front of six Viper seats

When done right, a parts-bin special can be a beautiful thing. This Dodge Durango Shaker concept for the 2016 SEMA show is one such vehicle, and it's easily our favorite Mopar debuting in Vegas. The key, of course, is pulling from the right bins. Take a tour and you'll see Charger, Challenger, and Viper pieces grafted onto this slick crossover. The featured special part is the big, 6.4-liter 392 Hemi V8 that's been dropped under the hood; it's sourced from the SRT Challenger and Charger where it makes 485 horsepower and 475 pound-feet of torque. With that in place, the fabricators cut a big hole in that hood for the Challenger's awesome optional shaker scoop. It wasn't an easy installation; it required a custom spacer for the intake to make sure everything lined up with the hole properly. View 17 Photos Apparently there were some Viper seats lying around, so six of them were stuck into this Durango. Makes sense. It does lose a bit of people-carrying capability as a result, since only two seats fit in each row, and the seats don't fold for extra cargo room. A Dodge spokesperson attested to the fact that all three rows are usable, if not totally comfortable. But then stock third-row seats aren't always that comfortable anyway. Seriously, though, Viper seats. We don't care how comfortable or usable the result is. Although you might not give it a second thought, even the fuel filler needed some special attention. This piece was also lifted from a Dodge Challenger, and it was taken along with the surrounding sheet metal. Because of the different orientation of the filler cover on the Challenger, the builders decided the easiest way to get it to fit was to chop the fuel filler section out and weld it onto the Durango. The designers also put a little blue Stig on the cover. And those are just the cool parts that were hard to install. This Durango features plenty of other slick details, like the custom bumpers, fender flares, and side skirts. Everything is painted B5 Blue with matte black and carbon accents all around. Up front, the bumper hides a pair of fog lights stolen from a Challenger Hellcat – and yes, they're the ones with intakes in the middle. The grille is also a custom piece, losing the standard crosshair design for better airflow. The fender flares cover up some seriously wide, 305-section tires at all four corners, which are hauled down by Hellcat brakes. The rear bumper bumper contains a stylish center-exit exhaust with dual tips.