2012 Dodge Ram 3500 St Crew Diesel 6speed Dually 13k Mi Texas Direct Auto on 2040-cars

Auto blog

Marchionne nixes talk of a reborn Dodge Viper

UPDATE: According to Automobile Magazine's Todd Lassa, FCA chief Sergio Marchionne shot down the idea of a reborn Viper, saying "it's not in the plan." Marchionne was referring to Fiat Chrysler's five-year plan, which we've been covering in bits and pieces as the news filters out. But it's not out of the realm of possibility, apparently, as Marchionne reportedly said he'd be happy to see the reptilian supercar back in production. And it's not all bad news, anyway. A reborn Alfa Romeo 8C will get a carbon-fiber chassis holding a mid-mounted twin-turbo V6. With more than 700 horsepower, including an electrically-driven front axle, the car should hit 62 mph in fewer than 3 seconds. Also, three versions of a Maserati Alfieri will be produced, including a convertible. An electrified all-wheel-drive powertrain is planned. So, performance is coming from FCA, it just may not be from Dodge. View 36 Photos First came the mourning for the Dodge Viper, which ended production last year. Then came the Viper's continued sales run as a "Zombie Car;" we just wrote about how the Viper has racked up 11 sales so far this year, two of them in April. Now Car and Driver reports that the two-seater snake will return shorty for its second encore after being discontinued in 2009. The mag isn't equivocal about it, either, writing, "trust us: A new Viper is happening." It won't, however, be the same Viper that brought ten-cylinder brass knuckles to shake down other coupes for their wallets and jewelry. CD says we should expect the same front-mid-engine layout and rear-wheel drive tucked into a new spaceframe. That engine will lose two cylinders, with Chrysler's next-gen, aluminum-block V8 Hemi slotting into the engine bay. The previous Viper's V10 had grown to 8.4 liters and 640 horsepower by the time it drove into the sunset. CD guesses the coming Viper will start with a naturally-aspirated version of the Hemi V8 working up around 550 horsepower. Healthy doses of aluminum and carbon fiber would restrain the car's weight, on top of the weight loss from swapping an iron V10 for an aluminum V8. SRT could tart up the horsepower with a few performance trims, before a supercharged V8 with 700-plus horsepower arrives at some point after launch. The mag also suspects the initial offering will be a convertible, the hardtop appearing "a few years after launch," which could coincide with the more powerful engine. A row-your-own shifter will sit between the seats.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Dodge Charger and Challenger will live on, but a new Viper is unlikely

BALOCCO, Italy — As FCA's latest five-year plan was presented last week, most of the day was focused on four brands — Jeep, Ram, Maserati and Alfa Romeo. That left a lot of people wondering about the future of the Chrysler, Fiat and Dodge nameplates. At the last five-year event, Dodge was one of the main features. We heard plans for an expanded lineup that included refreshed versions of the Viper, Challenger and Charger, the last two riding on the Alfa Romeo Giorgio platform. Times sure have changed. Dodge isn't going away, but the brand will be narrowed and focused. Performance is the name of the game, but don't look for a new Viper anytime soon. FCA CEO Sergio Marchionne simply said it's "not in the plan." Marchionne thought it was a great idea but that it couldn't live on as a standalone product. If it does eventually return, expect it to share parts with other FCA products, possibly with one of the upcoming Maseratis. On the other hand, Marchionne confirmed that both the Dodge Challenger and Charger will continue to live on. In the last five-year plan, FCA said that the pair would share underpinnings with future Alfa Romeos. That was promising news for those hoping for smaller, lighter versions of each model that would be better suited to fight models like the Ford Mustang and Chevy Camaro. It seems the Alfa Romeo platform is off the table. Marchionne said the current LX platform would indeed live on, though it would be "unrecognizable" compared to what we have today. The LX architecture is ancient, and, although it's been continuously updated, its basic bones date back to the DaimlerChrysler days. Marchionne said that the Alfa platform just doesn't have the character American shoppers are looking for in those vehicles. It's unclear when the next iteration of the Charger and Challenger will arrive, but expect another refresh sometime before 2022. Look for an updated version of the tried-and-true Hemi V8. Rumors continue to swirl about a larger and more powerful 7.0-liter variant dubbed the Banshee, but we'll have to wait and see how that pans out. Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.