2006 Dodge Ram 3500 Laramie 6 Speed Manual Diesel 4x4 on 2040-cars

Auto blog

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

2019 Dodge Charger SRT Hellcat Octane Edition fuels your dreams for a limited time

Few automakers love special-edition models quite as much as FCA. It's particularly prevalent in the Jeep and Ram lineups, but other makes get some love, too. Take a look at the new 2019 Dodge Charger SRT Hellcat Octane Edition, a special blacked-out model that's set to arrive at dealerships this fall. The car is available to order now, but Dodge says the books will only be open for a limited amount of time. The Octane Edition is available in two appropriately named colors: Pitch Black and White Knuckle. A pair of matte black stripes run down the middle of the car, flanked on both sides by a thin Octane Red stripe. The 20-inch wheels are painted gloss black and have a knurled bead to keep the tire from slipping on the rim. The Brembo brake package is included, with the six-piston front and four-piston rear calipers painted Octane Red to match the stripes. Inside, the Octane Edition gets houndstooth inserts in the SRT sport seats. There are red Hellcat logos, red seat belts and red stitching on the doors, seats, dash center console and steering wheel. The Octane Package adds $1,495 to the $68,740 base MSRP of a 2019 Charger Hellcat. Like all Hellcat models, the Charger comes with a supercharged 6.2-liter Hemi V8 making 707 horsepower and 650 pound-feet of torque. Power is sent to the rear wheels through an eight-speed automatic. Changes for '19 include a new grille with two inlets to feed more air under the hood. The cars also get launch control, line lock, a cooler for the supercharger as well as a torque reserve system that preloads the supercharger for better launches.

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.