2006 Dodge 3500 1 Ton Dually Quad Cab on 2040-cars

Auto blog

2018 Dodge Challenger SRT Demon First Drive | Don’t fear the Demon

"If you're not hurt, we'll be really pissed. If you are hurt, we'll still be pissed, but not quite as pissed." These are the words from Jim Wilder, the vehicle development manager of the 2018 Dodge Challenger SRT Demon, that echo through our head as we slide behind the wheel of the car for the first time. He was warning us about driving beyond our abilities, and keeping the car out of the wall. With 840 horsepower and 770 pound-feet of torque on tap from its supercharged, 6.7-liter V8, the Demon does 0-60 miles per hour in 2.3 seconds, and 0-30 mph in a second flat. If something does go wrong, it'll happen quickly. Following that talk, we had our guts sloshed as a passenger in a blurry eighth-mile run, giving us a taste of the G forces (the Demon can pull 1.8 G in a straight line) we'd feel when we got in the driver's seat for our own pass down the drag strip. We're already sweating. It had rained - you could describe it as torrential - the day before. The grassy parking areas surrounding Lucas Oil Raceway were still flooded, but any water on the pavement had evaporated and hung in the air. Combined with the heat, we were sticky and uncomfortable. In Drag Mode, the Dodge Demon's air conditioning turns off. Any condensation that it could leave on the track would be a problem, plus we need to reduce parasitic power losses for a faster run. The system is still working, though, the refrigerant diverted to the chiller system cooling the air coming into the engine. There's still condensation, but the Demon collects it on a catch pad to keep it from ending up on the pavement. We're also required to roll the windows up when entering the drag strip. For one thing, it helps keep the smoke out of the cabin during the pre-staging burnout. So, yeah, it's hot as Hell in the Demon. We pull through the water box and run through the sequence – which involves holding the "OK" button on the steering wheel usually used to navigate menus, and applying a specific amount of brake pressure before getting on the throttle to initiate the burnout. This gets any crud off the rear tires and heats up the rubber. There are multiple ways to launch the Demon. We had an instructor sitting in the passenger seat as we pulled up to the beams that trigger the Christmas tree at Lucas Oil Raceway. He walks us through the most complicated of the three he had explained to us just minutes before when we were in the passenger seat.

Dodge idles Viper production again at Conner Avenue

You've got to hand it to Dodge for having the gumption to put the original Viper into production in the first place. It was, after all, much more of an emotional decision than a practical one, and a move which saw the first production V10 engine placed in a road car - long before the advent of the Lamborghini Gallardo, Audi R8, Porsche Carrera GT or Lexus LFA, not to mention the other Ford, BMW and Volkswagen Group models that used such engines.
It's now been 22 years since the first Viper entered production and the Viper still rolls on several generations later, but we're sad to say that courageous decision has not always been met with overwhelming sales success. In fact parent Chrysler was forced to idle the Conner Avenue plant where the Viper is made back in April due to slow sales. And while production resumed again as planned on June 23, it apparently didn't do the trick.
As a result, Chrysler corporate communications chief Shawn Morgan revealed to Autoblog that the assembly line has been shut down again for another two weeks. The line was up and running for nearly two full work weeks from June 23 until the holiday weekend that started on Thursday, July 3. But instead of coming back online today as planned, it's been idled again for the weeks of July 7 and 14. That means it will be July 21, at the earliest, before the serpentine supercars start slithering down the assembly line at Conner Avenue again. Once it does, however, production is set to resume at the same pace it was before the shutdown.

Dodge puts kibosh on Challenger ACR rumors

In 2011, after the end of the Gen IV Dodge Viper and its ACR trim, Dodge took a Challenger ACR concept to the SEMA show. In October of last year, trusted FCA-focused outlet Mopar Insiders heard from its sources that something of the kind could finally be in the works, word being the automaker "is quietly working on a surprise to help celebrate the 50th anniversary of the Challenger nameplate." Last week, trusted FCA-focused outlet Allpar got more details from its own source, "Muther," on the specs and aspirations for a Challenger supposedly meant as a last big hurrah before the next generation appears in 2023. Now, we find out the Challenger ACR is a ghost, Autoweek reporting, "According to a spokesperson from Dodge, it's not happening." That brief denial is all the automaker had to say about it. Assuming Dodge isn't hiding anything, we're more surprised at detailed erroneous intel being shared with both MI and Allpar than we are about the track-day seducement Challenger ACR being bogus. A tale about Dodge engineering a Viper-like makeover for its number one muscle car so as to shame the 2020 Ford Mustang Shelby GT500 and Camaro ZL1 around a track would have been compelling enough. But word that Dodge wanted the Challenger ACR to breathe down the dearly departed neck of the Viper ACR around Road America, well, that was a crate of Hemi-powered wild. The implied impertinence of such a target is worrisome enough, and the weight loss goal would have added an extreme dimension to the ACR brand. The Neon ACR and Viper ACR didn't give up more than 100 pounds compared to their standard counterparts. The insiders spoke of the Challenger getting under 4,000 pounds, in part thanks to an optional passenger's seat. The diet would have required losing 400 pounds in a best-case scenario, which would still leave the big coupe 500-plus pounds heavier than a Viper ACR. Back to that impertinence... We'll likely never know what really happened with the Challenger ACR, so we'll stick it in the X-Files drawer between Big Blue and Chinga. Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.