08 Dodge Cummins Bighorn 4x4 Crew Cab Dually on 2040-cars

Auto blog

Barracuda's Dodge branding no biggie, but what about engines?

Rumors about a revival of the Barracuda nameplate have been circulating for years now, though which brand it might fall under has been a bit of a mystery. Initial speculation had the car labeled an SRT product, but that acronym has since returned to its former role as a sub-brand for top-performance Mopars. Thanks to leaks from a recent FCA dealership event, we know the Barracuda is back on the table but will be sold under the Dodge umbrella, a move that has been generating a bit of ire from Pentastar fanatics, as the car was originally part of the defunct Plymouth brand. Given what's known about the new model, however, the badge is the least of my concerns about the new car. Let's start with the re-branding itself. This isn't the first time Chrysler has shuffled models around to different brands. The current-generation Viper spent two years as the flagship model under the SRT banner, only to return to Dodge for 2015 when SRT resumed its former role as a sub-brand. Years ago, the Neon was sold as a Plymouth, a Dodge, and a Chrysler model, depending on where you shopped for one. When Plymouth ceased to exist, the last few years of Prowler production got Chrysler badges instead. Then there's the new Jeep Renegade, a model whose name was born out of a trim level. The Barracuda might not turn out to be a muscle car in the way we currently define them. Further examples of naming liberties taken throughout automotive history could fill a book, but suffice it to say that these days a model's name has very little to do with the vehicle itself or any legacy it might have. The Barracuda name might be a particularly sacred cow with enthusiasts, but to me, a much bigger concern is the fact that the car might not turn out to be a muscle car in the way we currently define them. News from the Fiat Chrysler dealer briefing earlier this week indicates that when the next Charger debuts it will share its platform with the Barracuda, much the way the Charger and Challenger are twinned now. One difference is that the Barracuda is tipped to be offered as a convertible, while the modern Challenger is tintop-only. The Charger and Barracuda will use the rear-drive platform developed for Alfa Romeo's new Giulia, itself designed as a BMW M3 fighter both from a dimensional and dynamic standpoint; the Barracuda is expected to be slightly smaller than the current Challenger.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Dodge Demon's deliverer? FCA files for 'Angel' trademark

We've driven the Dodge Demon, and despite its satanic overtones and 840 freakin' horsepower under the hood, the car is actually quite well-behaved. At least it didn't bite our head off or drag us into any sort of inferno. Still, Dodge might be looking to balance its lineup with something with a bit more righteous, as FCA has filed for a trademark of the moniker "Angel."... According to the United States Patent and Trademark Office, FCA filed the application on July 17, 2017, and it applies to "Motor vehicles, namely, passenger automobiles, their structural parts, trim and badges." Essentially, that's all the information we have to go on at this point. It could mean that Dodge is planning to further capitalize on the Demon name by creating another variant, or a completely different car. But what's the opposite of the Demon? Could it be a more road-friendly version of the drag-focused Demon? (And wouldn't that just be a Hellcat Widebody with more power?) Maybe it's a performance hybrid, as FCA CEO Sergio Marchionne recently said that the automaker would electrify half its fleet by 2022. For now, we can merely speculate as to what the Angel would be. And you can, too. Get at it in the comments section, below. And while you're at it, what name do you think FCA should trademark next, and what sort of car would that be?Related Video: Related Gallery 2018 Dodge Challenger SRT Demon: First Drive View 37 Photos News Source: US Patent and Trademark Office via FCA Authority Auto News Chrysler Dodge Future Vehicles Performance FCA trademark dodge demon