03 Dodge Ram 3500 Slt Quad Cab Dually Long Bed 5.9l Cummins Diesel 1owner on 2040-cars

Auto blog

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

VLF Force 1 V10 is a rebodied Viper priced like a Lamborghini

It would appear that Henrik Fisker is done with hybrids. His latest project, called the Force 1, packs an oversized V10 engine with no electric assist in sight and all the environmental credentials of a herd of flatulent cattle. Alongside the Karma-based, Corvette-powered Destino, the Force 1 is the second product from VLF Automotive. Fisker has taken partnership in the new firm as chief designer alongside chairman Bob Lutz and CEO Gilbert Villarreal. The company isn't saying explicitly what the Force 1 is based on, but it doesn't take a CSI team to trace its roots back to the Dodge Viper. Never mind that it's being built in Auburn Hills – the same Detroit suburb where Chrysler is headquartered – or that it was jointly developed by Fisker and professional Viper racer and dealer Ben Keating. It also happens to be powered by an 8.4-liter V10, and there aren't many of those kicking around the industry. Instead of the Viper's 645 horsepower and 600 pound-feet of torque, the Force 1's ten-cylinder engine is optimized to deliver 745 hp and 638 lb-ft. That, according to VLF, is enough to send the coupe rocketing to 60 in 3.0 seconds flat, covering the quarter-mile in under 11 seconds on its way to a top speed of 218 miles per hour. The power is transmitted to the Pirelli PZero rubber through a six-speed manual, but VLF says it will fit it with an automatic at the customer's request. Around that massive engine and two-seat cockpit, Fisker designed a new shape that, for better or for worse, looks way more aggressive than the Viper's. The Force 1's proportions are tellingly super-snake, but the curves are replaced by some very angry-looking angles and vents. Its head- and taillights are ultra thin, and the deep-dish, split-four-spoke wheels seem to visually split the difference between the three-spoke wheels on the original Viper and the five-spoke alloys it wears today. If you doubted the Force 1's origins before, the interior ought to give it away, with its wide tunnel and familiar surfaces. Only VLF has refinished it in leather, suede, and Alcantara, all diamond stitched with contrasting thread to help position this as a more luxurious prospect than the Dodge. It even fit between the seatbacks place for two champagne bottles that we hope nobody would consider consuming before trying to handle that much power. Of course, none of this will come cheap.

FCA to invest $4.5B for new Detroit plant, expanded production at current facilities

We expected some shifts in manufacturing plans as Fiat Chrysler plans to begin electrifying its Jeep brand, but this news bodes well for Michigan. FCA announced today that it would spend $4.5 billion to expand production in the state, including building a new assembly plant in Detroit and increasing capacity at five other facilities in the state. The plan, which FCA says will create nearly 6,500 new jobs, will help to meet increasing demand for Ram and Jeep products, and to electrify Jeep models. $1.6 billion will be set aside to transform the Mack Avenue Engine Complex into a site to build the next generation of Jeep Grand Cherokee, as well as an unspecified, new three-row Jeep model. FCA says this part of the plan will create 3,850 new jobs. FCA is increasing its investment in the Warren Truck plant to $1.5 billion in order to continue building the Ram 1500 Classic, as well as the new Jeep Wagoneer and Grand Wagoneer, creating 1,400 new jobs. FCA says that the new Ram 1500 Heavy Duty will still be built in Saltillo, Mexico. At FCA's Jefferson North facility, the automaker will invest $900 million to upgrade the plant. This site will continue to build the Dodge Durango, as well help build the next Jeep Grand Cherokee. FCA expects this to create 1,100 new jobs. As Jeep plans to electrify models in its SUV lineup, each of the above plants will produce plug-in hybrid versions of the Jeep models produced there, "with flexibility to build fully battery-electric models in the future," the company said in its announcement. "Three years ago, FCA set a course to grow our profitability based on the strength of the Jeep and Ram brands by realigning our U.S. manufacturing operations," said FCA CEO Mike Manley, referring in part to earlier investments in Illinois, Ohio and Michigan. "Today's announcement represents the next step in that strategy," Manley continued. "It allows Jeep to enter two white space segments that offer significant margin opportunities and will enable new electrified Jeep products, including at least four plug-in hybrid vehicles and the flexibility to produce fully battery-electric vehicles." Other investments include $119 million to move production of the 3.0-, 3.2- and 3.6-liter Pentastar engines from Mack I to the Dundee Engine Plant, and $400 million for increased capacity and 80 new jobs at the Sterling and Warren stamping plants. This comes at a time when FCA's U.S.