Slt Diesel 5.9l Cd 4x4 Tires - Front All-season Tires - Rear All-season Abs A/c on 2040-cars

Auto blog

Chrysler recalling 278,222 trucks and SUVs over bad rear axles

Chrysler has issued a recall of 278,222 light trucks and sport utility vehicles here in the United States. The reason: bad rear axles. Specifically, according to the National Highway Traffic Safety Administration, the rear axle pinion nut may lack a necessary adhesive patch, which could cause the nut to loosen. If this happens, the axle can lock up, which could cause all sorts of havoc on the road.
This is an expansion of the rear axle recall announced in October of last year, where 44,300 Ram 1500 and Dodge Dakota models were being called in. At that time, 12 accidents had been reported due to the faulty axle pinion nut.
Affected vehicles include Ram 1500 trucks from the 2009 to 2012 model years, Dodge Dakota models from the 2009 to 2011 model years, and both the Chrysler Aspen and Dodge Durango SUV twins, both from the 2009 model year only.

Hellcat motor 'fits like a glove' in the Wrangler and Gladiator, says Jeep

Just like "technically correct" is the best kind of correct, "technically possible" is the best kind of possible. Specifically, it's technically possible to slot a Hellcat crate motor into the Jeep Wrangler and Gladiator, as confirmed by Jeep brand chief Tim Kuniskis. Speaking to Australian media last week, Kuniskis went on to say that "everybody" keeps asking him if the supercharged, 6.2-liter Hellcat V8 fits in the Wrangler and Gladiator, and that the answer is yes. "It fits like a glove," said Kuniskis. But — there is a but — the fitment is so close for comfort, it makes the combination one that Jeep can never produce. "There's no air space around the engine [...] so you have no crush space, you have nothing that can be used to absorb energy in a crash. It's not a problem to put it in — other than emissions and fuel economy — except it would never pass any crash tests, and that's a problem," as Kuniskis told Drive. However, since the Hellcat is now out of the bag, it's probably only a matter of time until hobbyists with access to these engines will start putting them into Wranglers and Gladiators. And with the time-honored piece of advice — just don't crash into anything — it'd be a combination worth seeing and hearing. Just to throw it out there, a "Hellcrate" engine costs less than $20,000 new. Kuniskis also said that Jeep is "gauging interest" for the J6 concept, one of the Easter Jeep Safari concepts that were just revealed. "[The J6] is just a concept at this stage. But that doesn't mean we're not going to gauge interest for it." However, he said justifying its production is apparently "tough."

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.