6.7l Cummins Turbo Diesel-slt-nvr Hitched-crew Cab-tx Trk-pwr Seat-nice-ex Brake on 2040-cars

Auto blog

Speedkore AWD twin-turbo Carbon Charger, best birthday gift ever

The backstory the Speedkore Performance AWD twin-turbo Carbon Charger teased a couple of weeks ago might be cooler than the car itself. Alan Palermo commissioned the carbon-fiber-bodied Dodge Demon Speedkore brought to SEMA last year, the one that supplanted the 6.2-liter Hellcat V8's supercharger with twin 6875 Precision Billet T4 turbos. That blasted the Demon's usual 840 horsepower up to 1,400 hp at the flywheel, 1,203 hp at the rear tires, good for an 8.77-second quarter-mile time at 162 miles per hour. Palermo's older brother remarked, "He liked the car but was more of a four-door guy," so Alan commissioned the AWD Carbon Charger as a 65th birthday gift for his sibling. Speedkore worked with Magnaflow on the sedan, starting with a 2019 Charger Pursuit as a base. The Wisconsin tuner secured a 2020 widebody Charger from Dodge, then 3D-scanned the bodywork to create the molds reproducing most of the sheetmetal in pre-preg carbon fiber. The hood, bumpers, fenders, rockers, rear spoiler, and rear diffuser are all fashioned from the lightweight stuff.  Beyond those Precision turbos laid in by Gearhead Fabrications, Speedkore installed a custom upper plenum, Boost Leash C02 progressive boost controller, custom Thitek heads, a Fore Innovations triple-pump fuel system feeding Injector Dynamics 1,700-cc injectors, and custom HP Tuners engine software calibration. Test results showed 1,525 hp at the crank when running 26 pounds of boost.  Hellraiser Performance engineered a new transmission working an FTI torque converter at one end and a carbon fiber driveshaft at the other. Instead of fortifying an off-the-shelf AWD system, Traction Products supplied a custom transfer case machined from billet shunting power to a set of Bogart Competition Series wheels wearing Mickey Thompson ET street rubber.  Speedkore fitted last year's Demon with a front-exit twin exhaust, with a single opening on each front fender, and left the rear bumper cutouts for the traditional exhaust empty. With the Carbon Charger sedan more of a family guy, Magnaflow sorted out a quad-pipe front-exit exhaust with two openings on each front fender, and ran a three-inch stainless steel Competition Series exhaust to the rear. The driver can switch between the two, the latter version providing a "moderate interior sound."  The folks at Speedkore say they'll keep tweaking the Carbon Charger after the show to get it right for the senior Palermo. We say, "Happy birthday, sir. Enjoy."

Race Recap: Rolex 24 at Daytona was fast and feisty

Let the record show that victory at the 2015 Rolex 24 at Daytona went to the No. 02 Chip Ganassi Racing with Felix Sabates Target/Ford EcoBoost Riley DP driven by Verizon IndyCar drivers Scott Dixon and Tony Kanaan and NASCAR drivers Jamie McMurray and Kyle Larson. The winner did 740 laps to cover 2,634.3 miles in 24 hours and 57.667 seconds. That's a statement to this year's pace in spite of 18 cautions, two more than last year: the Michael Shank Racing Ligier got pole with a time of 1:39.194, slower than last year's pole time of 1:38.270; however, the winning car last year only did 695 laps. The fight for top honors was shaved to a four-car battle over the first third of the event. The No. 02 Ganassi car took the lead on the first lap, swapping it well into the night with the No. 01 Ganassi car, the No. 10 Wayne Taylor Racing Corvette DP, and the defending champion No. 5 Action Express Corvette DP, all of them staying within about 20 seconds of one another. The Action Express car had a fuel connector come loose and lost three laps getting towed back to the pits to have it reattached, but was back in the lead 18 hours in. The No. 01 Ganassi car dropped out with recurring clutch problems 22 hours in, retiring not long after. A race-within-the-race is where the concluding action happened, a seven minute, 30-second dash from the end of the last caution to the checkered flag. During the penultimate pit stops with an hour to go, Dixon was in second place followed Jordan Taylor in the Wayne Taylor Racing DP into the pits but beat him out, taking the lead. The Action Express car was in third. In the last pit stops of the race, Dixon gained even more time, getting a four-second advantage over Taylor. Then a full-course caution came out twenty minutes before the finish when a Prototype Challenge car hit the wall and caught fire, bunching up the field. That closed the pits, but the Wayne Taylor Racing car had to pit during that yellow because of a miscalculation of driver time. No driver can be behind the wheel for more than four hours in a six-hour period but Jordan Taylor was going to go over, so he came in to swap out for brother Ricky. That cost the team any chance of second place, since they took an additional drive-through penalty for entering closed pits. When the track went green again, Sebastien Bourdais in the Action Express car stayed all over Dixon for the final five laps but couldn't get around him.

How to tune a car right: Part 3, tuning Mopar with OST Dyno

Not long ago, I wrote a story about a pony car tuned with a supercharger. The blower install had been done properly. Then the car's owner bolted on a set of great looking wheels wrapped in good looking but inexpensive rubber. On my first test drive, I couldn't get any of that supercharged sweetness to the ground. It was the perfect ride for parking in a Burger King parking lot on a Friday night. I tooled around on a Sunday drive, shaking my head that someone had spent five figures to get more power the right way, with a clean install, then wiped out the gains so thoroughly that the stock engine would likely have overwhelmed the tires. This got me thinking about the ways people ruin their quest for horsepower, either on the front end by not insisting on a clean install and paying the money for it, or on the back end with supplemental purchases like cheap tires or cheap gas. So I called three tuners, one focused on GM, one on Mopar, one on Ford, to find out what people should know about how to get the best power for their goals, and how to make sure they are able to use all that power. The first interview in this three-part series was with Blake Leonard at Top Speed Cincy in Cincinnati, Ohio, the second with Brandon Alsept at BA Motorsports in Milford, Ohio. This third and last interview is with Micah Doban at OST Dyno in Slippery Rock, Pennsylvania, a family business with more than 40 years of Mopar expertise specializing in Gen III Hemis, but tuning everything from land-speed cars and drag racers to Jeeps The interview has been edited for clarity and concision. Do people who come to OST generally know what they want? Probably 80% of the people who come in simply want more power with no particular ET goal [ET is a kind of bracket handicapped drag racing – ed.]. WhatÂ’s the best way to start a Mopar tune? The first thing is what people often skip, and that's to find a tuner or a shop. People will throw parts on their cars that the Internet said to, then go to a tuner who does things a different way, and [the tuner is] like ‘No we don't like to use these injectors, we don't like these parts.Â’ You have to find someone familiar with the parts that are on your car or that you're planning to put on your car. So having a goal and then finding a tuner who can help you with that goal is proper way to start. Exactly. And a lot of tuners have their own formula – and when I say tuner I mean someone that also does work to the cars.