2005 Dodge Ram 2500 Quad Hemi 4x4 Long Bed Auto 48k Mi Texas Direct Auto on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Stellantis not looking for further mergers, including with Renault

MILAN — Stellantis Chairman John Elkann on Monday denied the carmaker was hatching merger plans, responding to press speculation about a possible French-led tie-up with rival Renault. Elkann said that the Peugeot owner, the world's third largest carmaker by sales, was focused on the execution of its long-term business plan. "There is no plan under consideration regarding merger operations with other manufacturers," said Elkann, who also heads Exor, the Agnelli family holding company that is the largest single shareholder in Stellantis. After abandoning the Russian market, at the time its second largest after France, and reducing the scope of its global cooperation with Nissan, Renault has been seen as a potential M&A target. Speculation intensified after an electric vehicle market slowdown forced it last week to cancel IPO plans for its EV and software unit Ampere. Its market cap remains stubbornly low at little over 10 billion euros ($10.8 billion) despite a financial recovery over the past few years. Stellantis, the product of a 2021 merger between France's PSA and Fiat Chrysler and one of the most profitable groups in the industry, has a market cap of more than 85 billion euros when unlisted shares are factored in. It has a 14 brand portfolio also including Citroen, Jeep, Opel and Alfa Romeo. NEWSPAPER REPORT Italian daily Il Messaggero had said on Sunday that the French government, which is Renault's largest shareholder and also has a stake in Stellantis, was studying plans for a merger between the two groups. A spokeswoman for Renault said on Monday the group did not comment on rumors. France's Finance Ministry had declined to comment on Sunday. Stellantis has crossed swords with the Italian government, which has accused it of acting against the national interest on occasions. Industry Minister Adolfo Urso last week raised the prospect of the Italian government taking a stake in Stellantis to help to balance the French influence. Renault shares pared gains after Elkann's comments to stand 1.2% higher by 1220 GMT, having initially risen more than 4%. Stellantis CEO Carlos Tavares, a Portuguese-national, last week said in an interview with Bloomberg that the group was "ready for any kind of consolidation" and that its job was to make sure that it would be "one of the winners". Analysts, however, question the rationale of a Stellantis-Renault merger, which would also expand the group's excess capacity in Europe.

Driving the Jeep J6, Shakedown Challenger and other Mopar concepts

Mopar has been a one-stop-shop for factory-backed performance modifications and accessories on FCA products for a long time now. You want a 707-horsepower engine for your old Plymouth Belvedere? Mopar has you covered with the Hellcrate. Maybe you want a lift and off-roading lights on that newly-bought Wrangler? Mopar can accommodate those wants (or needs, we don’t judge) as well. We get to see some of the companyÂ’s weirdest creations every now and then, but rarely do we get the opportunity to drive the FCA Mopar concepts. ThatÂ’s what made this past Woodward Dream Cruise so special: We got to rip some of MoparÂ’s finest and most recent creations up and down Woodward Avenue. Everything from a 1971 Challenger restomod to the brand-new Easter Jeep Safari J6 concept was in attendance, so letÂ’s get right to it. Mopar Woodward View 6 Photos 1967 Plymouth Hellvedere This car is near the pinnacle of what you can do with off-the-shelf Mopar purchases. It was only a humble 1967 Plymouth Belvedere before Mopar dropped the 707-horsepower supercharged V8 from the Hellcat into the engine bay. Sound ridiculous? Yeah, it is. Other parts of it are new as well, including the disc brakes. Good call. However, Mopar didnÂ’t remove the classic car charm from the entire driving experience. The steering, for example, is surely as slow and inaccurate as it was back in 1967. That doesnÂ’t help matters when youÂ’re trying to put 707 horsepower to the pavement with less-than-ideal rear rubber. Floor it in damn near any gear of the Tremec six-speed, and the front end rises straight up as the rear kicks sideways with the force of many mules. There are no electronics such as traction control or stability control to step in and wrangle the car into submission. But hey, who wants them, anyway? The question remains: Should you buy a Hellcrate engine for your classic? If money were no object, the easy answer is yes. Have at it so long as you love smoky burnouts and excessive amounts of horsepower. Just make sure you know how to deal with that much power before you stick your right foot in it.   Dodge Challenger Shakedown View 15 Photos 2016 Dodge Shakedown Challenger Concept WeÂ’re going downhill in horsepower with this restomod, but the drivability and ease of driving goes way up. Dodge showed this “Shakedown” concept at SEMA awhile back, and as with most concept cars, getting a chance behind the wheel is a special opportunity.