2004 Dodge Ram 2500 4dr Quad Cab 4wd on 2040-cars

Auto blog

Junkyard Gem: 1991 Dodge Stealth R/T

Chrysler's relationship with Mitsubishi goes back to the early 1970s, when the first Mitsubishi Colt Galants arrived from Japan with Dodge Colt badging. Plenty of Mitsubishi-built Arrows and Ram 50s and Challengers followed, and the joint Chrysler-Mitsubishi plant in Illinois began building cars in 1988. By the 1990s, you could find Mitsubishi DNA throughout the American Chrysler family, and the Mitsubishi GTO was brought over to become the Dodge Stealth starting in 1991. Here's one of those first-year Stealths, now residing in a Colorado self-service boneyard. Four grades of Stealth were available here in 1991, with the R/T Turbo AWD at the very pinnacle. This car, a regular R/T, is one step down from that model but still a pretty quick machine for its time. MSRP was $25,155, or about $55,370 in 2022 dollars. The R/T got this naturally-aspirated DOHC 6G72 engine, displacing 3.0 liters and making 222 horsepower. If you got the turbocharged version in the R/T Turbo AWD (or the Mitsubishi 3000GT VR-4), power went up to 300 horses. The 3000GT (as the GTO was known here) was mechanically identical to this car but had slightly different styling. The GTO/3000GT/Stealth replaced the Mitsubishi Starion and its Chrysler/Dodge Conquest siblings, which were sold here from the 1983 through 1989 model years. The Starion was a rear-wheel-drive machine that competed for sales against the Toyota Supra and Nissan Z, while the Mitsubishi GTO was available with either front- or all-wheel-drive. As illustrated by this photo of the rear suspension, this car is a front-wheel-drive version. Americans loved automatic transmissions 30 years ago, nearly as much as we love them today, but this car has a proper five-on-the-floor manual. If you wanted the optional four-speed automatic, it cost 813 bucks ($1,790 today). The Stealth R/T AWD had a mandatory five-speed manual transmission. This car has been hit hard by junkyard shoppers and the ravages of time, but it was fairly luxurious when new. Air conditioning was standard equipment on the R/T, though not on the lesser Stealths. This car came close to 150,000 total miles, but fell a bit short of that milestone. The final year for the Dodge Stealth was 1996, though the Mitsubishi 3000GT remained available here through 1999. The Mitsubishi GTO held on through 2000 in its homeland. This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Outhandles the Lotus Esprit!

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Turn up the volume: Flat out in the Dodge Charger Scat Pack

The 2019 Dodge Charger R/T Scat Pack is a rare breed in the car market. It's a reasonably affordable large sedan with a huge honking V8 and rear wheel drive. You know, the perfect car for this Fourth of July. Or any day ending in Y, really. The R/T Scat Pack is the second most powerful version of the sedan with a 6.4-liter naturally aspirated V8 making 485 horsepower and 475 pound-feet of torque. Only the 707-horsepower Hellcat is a more powerful Charger. But power is only part of the story. The other part is the noise. The V8 has a gritty, dirty rumble to it. We recorded it cruising up on-ramps, down shifting, and got a few standing revs out of it. Check out the video to hear for yourself.