2000 Dodge Ram 2500 Quad Cab 4x4 on 2040-cars

Auto blog

Watch these Dodge Demons explode on a Texas drag strip

The Dodge Challenger SRT Demon is extremely quick. It can hit 60 mph from a dead stop in less time than it takes to read this sentence thanks to its supercharged 6.2-liter V8. That engine makes up to 840 horsepower and 770 pound-feet of torque, depending on what octane is running through the fuel lines. That's a ton of power going solely to the rear wheels. So much so that Dodge developed a number of features and a new set of tires specifically for the car. In our time with the Demon, the car took abuse run after run on a drag strip without skipping a beat, but it seems some actual owners aren't quite so lucky. Just take a look at what happened to a few of these cars. You can see the whole car shake and jitter right as the whole rear explodes in front of the tree. It seems the initial shock from the launch — the most taxing bit of any drag run — is what kills the differentials. Catastrophic failure is rarely pretty, but it is neat to see the whole thing occur in slow motion. Three more cars — four stock and one modified in total — suffered similar fates. Not a great look for Dodge or SRT. According to The Drive, a private drag event in Texas drew a number of Demon owners all trying to beat NHRA NHRA Top Fuel racer Leah Pritchett's time in her personal Dodge Demon — 42 stock Demons attended along with five modified cars. While no one managed to match her 9.65-second quarter-mile run, a few owners did dip below 10 seconds. Now, there are a few of caveats we must address. First, with any modified car, you run the risk of breaking something, even with a car that's set up from stock specifically for drag strips. Even a set of tires like the Mickey Thompsons shown in the video above can have an effect on driveline components. Horsepower may be king, but it's torque that's the rear killer. All that torque sends a shock through the car. Adding even more with aftermarket parts increases the risk of something failing. The modified car was apparently pushing out about 1,000 horsepower. That said, four of the five vehicles were stock, so any extra power or torque should theoretically be a non-factor. The drag strip's surface was maintained by a company called Mass Traction. FCA used Mass Traction during the Demon's development, so that too should be a non-factor in the part's failure. It's unclear what exactly caused the failures, though The Drive reports that FCA officials are investigating the matter. Related Video: This content is hosted by a third party.

Dodge Hornet supposedly snapped inside Alfa Romeo Tonale factory

It appears that someone in Stellantis' Pomigliano d’Arco Assembly Plant in Italy couldn't keep their cellphone to themselves. Video uploaded to the Alfa Romeo Club Italia Facebook page, then quickly removed, purports to show Dodge's brand-engineered version of the Alfa Romeo Tonale in the same factory where the Alfa will be built. The Dodge is expected to be called the Hornet, and there are a few differences between it and and Alfa Romeo, which is understandable. But if the screenshots on Twitter are accurate, then the Dodge looks a lot closer to the Alfa Romeo than perhaps anyone expected. The front fascia and hood fall in line with Dodge's design language. The Alfa grille is replaced by a narrow, stepped upper grille, and the hood is one of the vented units similar to those available for Dodge's R/T performance trims. And as Mopar Insiders noticed, the silhouette of this car's front end matches a vehicle silhouette Dodge showed during Stellantis' 2021 EV Day.   Inside, the Italian brand's crest in the steering wheel center cap is replaced by Dodge's twin slashes, and the steering wheel has been stripped of the large, curved paddle shifters the Tonale showed on its debut. There's still a start/stop button on the steering wheel, but where the Tonale has a driving mode dial on its dash, this supposed Hornet has another start/stop button. Dodge's push-to-start buttons are usually on the instrument panel, so our guess is that the wheel is a holdover for testing. On the center tunnel, the parking alert buttons and Italian Tricolore flag on the Alfa Romeo are replaced by three different buttons.   We've known Dodge has two electrified vehicles on the way, and the Hornet name has been low-key buzzing for two years. Fiat Chrysler applied to trademark the name in the U.S. in March 2020; at the time, it was thought a vehicle with that name could replace the Journey. In 2021, a July rumor out of Italy was the first whisper of the Hornet name being attached to the Alfa Romeo Tonale. In August, when Stellantis CEO Carlos Tavares said Dodge would get a PHEV in 2024, watchers pegged that model as the Hornet. That hybrid powertrain would show a year after the vehicle's launch, the Hornet anticipated as a 2023 model with the Tonale's turbocharged 2.0-liter four-cylinder. That engine could get the same 256 horsepower and 295 pound-feet of torque as the Tonale, or be boosted to satisfy Dodge's performance credentials.

Has Dodge stepped in it again with Scat Pack lawsuit?

Lawsuits are an unfortunate part of doing business in just about any industry, so the latest complaint filed by a California-based aftermarket firm against Chrysler would seem to be nothing more than business as usual. But this isn't the first time the two companies have sparred over this particular issue.
According to a report from Automotive News, the dispute revolves around the Scat Pack name that Chrysler first offered on the Charger, Coronet, Dart and Super Bee starting in 1968. Scat Enterprises, a manufacturer of crankshafts and other components for Dodges and other vehicles, sued Chrysler for using its name. A few years later the Scat Pack disappeared from the Dodge catalog.
Fast forward to August 2013 when Chrysler applied to register the Scat Pack name anew. The US Patent and Trademark Office turned down Chrysler's application, but the automaker proceeded anyway, unveiling new Scat Packs for the Challenger, Charger and Dart at last year's SEMA show.