2006 Dodge Ram 1500 Slt on 2040-cars

Auto blog

Watch these Dodge Demons explode on a Texas drag strip

The Dodge Challenger SRT Demon is extremely quick. It can hit 60 mph from a dead stop in less time than it takes to read this sentence thanks to its supercharged 6.2-liter V8. That engine makes up to 840 horsepower and 770 pound-feet of torque, depending on what octane is running through the fuel lines. That's a ton of power going solely to the rear wheels. So much so that Dodge developed a number of features and a new set of tires specifically for the car. In our time with the Demon, the car took abuse run after run on a drag strip without skipping a beat, but it seems some actual owners aren't quite so lucky. Just take a look at what happened to a few of these cars. You can see the whole car shake and jitter right as the whole rear explodes in front of the tree. It seems the initial shock from the launch — the most taxing bit of any drag run — is what kills the differentials. Catastrophic failure is rarely pretty, but it is neat to see the whole thing occur in slow motion. Three more cars — four stock and one modified in total — suffered similar fates. Not a great look for Dodge or SRT. According to The Drive, a private drag event in Texas drew a number of Demon owners all trying to beat NHRA NHRA Top Fuel racer Leah Pritchett's time in her personal Dodge Demon — 42 stock Demons attended along with five modified cars. While no one managed to match her 9.65-second quarter-mile run, a few owners did dip below 10 seconds. Now, there are a few of caveats we must address. First, with any modified car, you run the risk of breaking something, even with a car that's set up from stock specifically for drag strips. Even a set of tires like the Mickey Thompsons shown in the video above can have an effect on driveline components. Horsepower may be king, but it's torque that's the rear killer. All that torque sends a shock through the car. Adding even more with aftermarket parts increases the risk of something failing. The modified car was apparently pushing out about 1,000 horsepower. That said, four of the five vehicles were stock, so any extra power or torque should theoretically be a non-factor. The drag strip's surface was maintained by a company called Mass Traction. FCA used Mass Traction during the Demon's development, so that too should be a non-factor in the part's failure. It's unclear what exactly caused the failures, though The Drive reports that FCA officials are investigating the matter. Related Video: This content is hosted by a third party.

2013 Dodge Challenger V6 recalled for fire risk, owners asked not to drive

Chrysler has issued a recall for the V6 version of the 2013 Dodge Challenger (as pictured above in 2012MY) over the possibility of a wiring harness that could short circuit and lead to a fire. Owners of these V6 Challengers built from November 2012 through January 2013 are being urged to contact dealers immediately and, in the meantime, not to drive their cars or park in or near any buildings.
Chrysler estimates around 2,500 potentially affected Challengers are in owners' hands, while another 1,900 are still sitting on dealer lots. The total number of recalled vehicles is 4,459.
So far, Chrysler says that seven fires have been reported - none resulting in injuries. The company is instructing vehicle owners to contact their dealer to find out if their vehicle is included in the recall, but owners can also find the build date information of their vehicle by checking the label in the driver's door jamb.

2025 SRT Hellcat concepts as previewed by high schoolers

Fiat Chrysler Automobiles has some very talented designers in its ranks. Like any good company, though, the automaker is always on the lookout for early talent. Even if they're still in high school. One of those talent-seeking initiatives is the company's Drive for Design contest, an event open to tenth-, eleventh-, and twelfth-grade students that are hoping for a future in design. For this year's event, students from across the country were given a shot to design their vision for a 2025 model-year Dodge SRT Hellcat. The results are impressive, as you can see in the gallery above. First place went to Ben Treinen, from Archbishop Moeller High School in Cincinnati. Second place was the only award to go to a student outside the Rust Belt, with Macon, GA's Harrison Kunselman, a student at Mount de Sales Academy taking the silver. Third place was won by a metro Detroiter – Bloomfield Hills High School student Hwanseong Jang, while fourth went to Andrew Gombac of Loyola Academy in Wilmette, IL. According to FCA, all four winners will have their sketches on display at the 2016 Autorama at Cobo Center at the end of February. They'll also win some pretty nifty prizes. First place will get a new Apple MacBook Pro, while second, third, and fourth get the new Apple iPad Pro and Apple Pencil (arguably just as good of a prize for budding designers). All four finishers will also attend a three-week automotive design course at Detroit's prestigious College for Creative Studies, have dinner with FCA designers, and score three passes to Autorama. FCA will cover travel and lodging to Auburn Hills. Read on for the official blast from FCA. Related Video: FCA US Design Team Announces Winners of Drive for Design Contest January 19, 2016 , Auburn Hills, Mich. - The FCA US LLC Design team today announced four winners in this year's Drive for Design contest. The FCA US Drive for Design contest challenged U.S. high school students in grades 10-12 to design a Dodge SRT Hellcat for the year 2025. "The Drive for Design contest continues to be a great way for the FCA US Design team to connect with students that show an interest in art and design," said Mark Trostle – Head of Dodge and SRT Design, FCA US LLC.