08 Quad Cab Short Box 4x4 Flex Fuel Cd Player Auxiliary Input Tow Tube Steps on 2040-cars

Auto blog

2018 Dodge Challenger SRT Demon First Drive | Don’t fear the Demon

"If you're not hurt, we'll be really pissed. If you are hurt, we'll still be pissed, but not quite as pissed." These are the words from Jim Wilder, the vehicle development manager of the 2018 Dodge Challenger SRT Demon, that echo through our head as we slide behind the wheel of the car for the first time. He was warning us about driving beyond our abilities, and keeping the car out of the wall. With 840 horsepower and 770 pound-feet of torque on tap from its supercharged, 6.7-liter V8, the Demon does 0-60 miles per hour in 2.3 seconds, and 0-30 mph in a second flat. If something does go wrong, it'll happen quickly. Following that talk, we had our guts sloshed as a passenger in a blurry eighth-mile run, giving us a taste of the G forces (the Demon can pull 1.8 G in a straight line) we'd feel when we got in the driver's seat for our own pass down the drag strip. We're already sweating. It had rained - you could describe it as torrential - the day before. The grassy parking areas surrounding Lucas Oil Raceway were still flooded, but any water on the pavement had evaporated and hung in the air. Combined with the heat, we were sticky and uncomfortable. In Drag Mode, the Dodge Demon's air conditioning turns off. Any condensation that it could leave on the track would be a problem, plus we need to reduce parasitic power losses for a faster run. The system is still working, though, the refrigerant diverted to the chiller system cooling the air coming into the engine. There's still condensation, but the Demon collects it on a catch pad to keep it from ending up on the pavement. We're also required to roll the windows up when entering the drag strip. For one thing, it helps keep the smoke out of the cabin during the pre-staging burnout. So, yeah, it's hot as Hell in the Demon. We pull through the water box and run through the sequence – which involves holding the "OK" button on the steering wheel usually used to navigate menus, and applying a specific amount of brake pressure before getting on the throttle to initiate the burnout. This gets any crud off the rear tires and heats up the rubber. There are multiple ways to launch the Demon. We had an instructor sitting in the passenger seat as we pulled up to the beams that trigger the Christmas tree at Lucas Oil Raceway. He walks us through the most complicated of the three he had explained to us just minutes before when we were in the passenger seat.

Watch these Dodge Demons explode on a Texas drag strip

The Dodge Challenger SRT Demon is extremely quick. It can hit 60 mph from a dead stop in less time than it takes to read this sentence thanks to its supercharged 6.2-liter V8. That engine makes up to 840 horsepower and 770 pound-feet of torque, depending on what octane is running through the fuel lines. That's a ton of power going solely to the rear wheels. So much so that Dodge developed a number of features and a new set of tires specifically for the car. In our time with the Demon, the car took abuse run after run on a drag strip without skipping a beat, but it seems some actual owners aren't quite so lucky. Just take a look at what happened to a few of these cars. You can see the whole car shake and jitter right as the whole rear explodes in front of the tree. It seems the initial shock from the launch — the most taxing bit of any drag run — is what kills the differentials. Catastrophic failure is rarely pretty, but it is neat to see the whole thing occur in slow motion. Three more cars — four stock and one modified in total — suffered similar fates. Not a great look for Dodge or SRT. According to The Drive, a private drag event in Texas drew a number of Demon owners all trying to beat NHRA NHRA Top Fuel racer Leah Pritchett's time in her personal Dodge Demon — 42 stock Demons attended along with five modified cars. While no one managed to match her 9.65-second quarter-mile run, a few owners did dip below 10 seconds. Now, there are a few of caveats we must address. First, with any modified car, you run the risk of breaking something, even with a car that's set up from stock specifically for drag strips. Even a set of tires like the Mickey Thompsons shown in the video above can have an effect on driveline components. Horsepower may be king, but it's torque that's the rear killer. All that torque sends a shock through the car. Adding even more with aftermarket parts increases the risk of something failing. The modified car was apparently pushing out about 1,000 horsepower. That said, four of the five vehicles were stock, so any extra power or torque should theoretically be a non-factor. The drag strip's surface was maintained by a company called Mass Traction. FCA used Mass Traction during the Demon's development, so that too should be a non-factor in the part's failure. It's unclear what exactly caused the failures, though The Drive reports that FCA officials are investigating the matter. Related Video: This content is hosted by a third party.

Inline-6 Hemi replacement on the cusp of production from Stellantis

It appears that Stellantis is ready to put its long-rumored inline-six into production at its Saltillo, Mexico plant, possibly marking the beginning of the end of Chrysler's long-running 5.7L Hemi V8. But so far, the automaker's American brands have remained mum on where exactly the new turbocharged "Tornado" I6 may land. Stellantis powertrain blog Stellpower (by way of Muscle Cars & Trucks) spotted an entry for a new "GME T6" inline-six engine on the Saltillo facility's web site, suggesting that it was either in production or close to it. That entry has since been removed, but the mystery remains.  We've been hearing tidbits here and there about this new inline engine for years, but this is the first time we've seen anything suggesting its arrival is imminent. Usually, such a significant powertrain update would coincide with the launch of a new product to showcase it. So far, Stellantis has remained mum, even overseas, about where this engine is destined to reside. 2022 model year vehicles are likely off the table entirely.  But while it's common for new engines to debut with new cars and trucks, it's not a universal truth. Ford's Coyote V8 missed the corresponding Mustang refresh by a year, for example, orphaning the 2010 model and its much-needed styling updates with the old 4.6L V8 (and the 3.8L V6, for that matter; the 3.7L Duratec was also late to that party). Even sticking just to Stellantis, the JL Wrangler's powertrains have been a work in progress since it arrived back in 2018. The standard V6 and 2.0-liter turbo-4 debuted at launch; the EcoDiesel, 392 and 4xe all came later.  And 4xe may be the model by which to measure our expectations. Its introduction didn't come completely out of nowhere, but it was rather sudden for what turned out to be such a solid offering. That bodes well for the company's existing Hemi-powered trucks and SUVs. The Ram 1500, Jeep Grand Cherokee and Wagoneer are all strong candidates to receive the new Hemi replacement, as all would greatly benefit from even small improvements in fuel economy. If there's to be a future for the Dodge Charger and Challenger and Chrysler 300, they'd benefit too. And how about a Gladiator with the wick turned up, positioned as its equivalent to the Wrangler 392. Turn that Tornado into a Dust Devil. Don't worry; we've got plenty more where that came from.  Related Video This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.