06 Full Size Quad Cab on 2040-cars

Auto blog

Watch these Dodge Demons explode on a Texas drag strip

The Dodge Challenger SRT Demon is extremely quick. It can hit 60 mph from a dead stop in less time than it takes to read this sentence thanks to its supercharged 6.2-liter V8. That engine makes up to 840 horsepower and 770 pound-feet of torque, depending on what octane is running through the fuel lines. That's a ton of power going solely to the rear wheels. So much so that Dodge developed a number of features and a new set of tires specifically for the car. In our time with the Demon, the car took abuse run after run on a drag strip without skipping a beat, but it seems some actual owners aren't quite so lucky. Just take a look at what happened to a few of these cars. You can see the whole car shake and jitter right as the whole rear explodes in front of the tree. It seems the initial shock from the launch — the most taxing bit of any drag run — is what kills the differentials. Catastrophic failure is rarely pretty, but it is neat to see the whole thing occur in slow motion. Three more cars — four stock and one modified in total — suffered similar fates. Not a great look for Dodge or SRT. According to The Drive, a private drag event in Texas drew a number of Demon owners all trying to beat NHRA NHRA Top Fuel racer Leah Pritchett's time in her personal Dodge Demon — 42 stock Demons attended along with five modified cars. While no one managed to match her 9.65-second quarter-mile run, a few owners did dip below 10 seconds. Now, there are a few of caveats we must address. First, with any modified car, you run the risk of breaking something, even with a car that's set up from stock specifically for drag strips. Even a set of tires like the Mickey Thompsons shown in the video above can have an effect on driveline components. Horsepower may be king, but it's torque that's the rear killer. All that torque sends a shock through the car. Adding even more with aftermarket parts increases the risk of something failing. The modified car was apparently pushing out about 1,000 horsepower. That said, four of the five vehicles were stock, so any extra power or torque should theoretically be a non-factor. The drag strip's surface was maintained by a company called Mass Traction. FCA used Mass Traction during the Demon's development, so that too should be a non-factor in the part's failure. It's unclear what exactly caused the failures, though The Drive reports that FCA officials are investigating the matter. Related Video: This content is hosted by a third party.

VLF Force 1 V10 is a rebodied Viper priced like a Lamborghini

It would appear that Henrik Fisker is done with hybrids. His latest project, called the Force 1, packs an oversized V10 engine with no electric assist in sight and all the environmental credentials of a herd of flatulent cattle. Alongside the Karma-based, Corvette-powered Destino, the Force 1 is the second product from VLF Automotive. Fisker has taken partnership in the new firm as chief designer alongside chairman Bob Lutz and CEO Gilbert Villarreal. The company isn't saying explicitly what the Force 1 is based on, but it doesn't take a CSI team to trace its roots back to the Dodge Viper. Never mind that it's being built in Auburn Hills – the same Detroit suburb where Chrysler is headquartered – or that it was jointly developed by Fisker and professional Viper racer and dealer Ben Keating. It also happens to be powered by an 8.4-liter V10, and there aren't many of those kicking around the industry. Instead of the Viper's 645 horsepower and 600 pound-feet of torque, the Force 1's ten-cylinder engine is optimized to deliver 745 hp and 638 lb-ft. That, according to VLF, is enough to send the coupe rocketing to 60 in 3.0 seconds flat, covering the quarter-mile in under 11 seconds on its way to a top speed of 218 miles per hour. The power is transmitted to the Pirelli PZero rubber through a six-speed manual, but VLF says it will fit it with an automatic at the customer's request. Around that massive engine and two-seat cockpit, Fisker designed a new shape that, for better or for worse, looks way more aggressive than the Viper's. The Force 1's proportions are tellingly super-snake, but the curves are replaced by some very angry-looking angles and vents. Its head- and taillights are ultra thin, and the deep-dish, split-four-spoke wheels seem to visually split the difference between the three-spoke wheels on the original Viper and the five-spoke alloys it wears today. If you doubted the Force 1's origins before, the interior ought to give it away, with its wide tunnel and familiar surfaces. Only VLF has refinished it in leather, suede, and Alcantara, all diamond stitched with contrasting thread to help position this as a more luxurious prospect than the Dodge. It even fit between the seatbacks place for two champagne bottles that we hope nobody would consider consuming before trying to handle that much power. Of course, none of this will come cheap.

Dodge Journey and Fiat Freemont engine-cover recall affects 350k CUVs

FCA is recalling 349,731 examples of the 2011-2015 Dodge Journey and Fiat Freemont worldwide to better secure their engine covers. Of these affected vehicles, there are 144,416 in the US, 43,679 in Canada, 46,231 in Mexico, and 115,405 elsewhere. About 10 percent of them are also still at dealers, according to the automaker. Only models with the 2.4-liter four-cylinder engine are affected by this campaign. According to the company, the engine covers on these vehicles can be dislodged, and this can pose a fire risk if the loose part comes in contact with hot exhaust components. Warning signs of this happening include a noise under the hood, burning smell or a light on the instrument panel. The problem was discovered after three incidents on rough roads in Chile, and there was one minor injury there. According to FCA US spokesperson Eric Mayne to Autoblog, there have been eight occurrences of this issue reported in the US, but these were all related to "heat damage." There have been no reported injuries here. To fix the problem, dealers will install new engine-cover retainers on the affected models. These repairs will begin in August. As always for recall repairs, owners won't be charged. Statement: Engine Cover July 22, 2015 , Auburn Hills, Mich. - FCA US LLC is voluntarily recalling an estimated 144,416 crossover utility vehicles (CUVs) in the U.S. to better secure their engine covers. Engine covers in certain vehicles may become dislodged. If they come in contact with exhaust components, it may pose a fire risk. This condition was discovered during an FCA US investigation of three incidents in Chile. In each case, the vehicle had been driven extensively on unpaved or uneven surfaces. The Company is aware of a single related injury, described as minor. Affected are 2011-2015 Dodge Journey and Fiat Freemont CUVs equipped with 2.4-liter, four-cylinder engines. FCA US will install upgraded engine-cover retainers in these vehicles. The remedy will be available when customer notification begins next month; service will be performed free of charge. Vehicles equipped with six-cylinder engines are not affected. Additional Journey and Freemont populations also are subject to this campaign. They comprise an estimated 43,679 vehicles in Canada; 46,231 in Mexico; and 115,405 outside the NAFTA region. Of the 349,731 total vehicles subject to this campaign, approximately 10 percent remain in dealer hands.