1959 Dodge D100 Truck on 2040-cars

Auto blog

Dodge Hornet supposedly snapped inside Alfa Romeo Tonale factory

It appears that someone in Stellantis' Pomigliano d’Arco Assembly Plant in Italy couldn't keep their cellphone to themselves. Video uploaded to the Alfa Romeo Club Italia Facebook page, then quickly removed, purports to show Dodge's brand-engineered version of the Alfa Romeo Tonale in the same factory where the Alfa will be built. The Dodge is expected to be called the Hornet, and there are a few differences between it and and Alfa Romeo, which is understandable. But if the screenshots on Twitter are accurate, then the Dodge looks a lot closer to the Alfa Romeo than perhaps anyone expected. The front fascia and hood fall in line with Dodge's design language. The Alfa grille is replaced by a narrow, stepped upper grille, and the hood is one of the vented units similar to those available for Dodge's R/T performance trims. And as Mopar Insiders noticed, the silhouette of this car's front end matches a vehicle silhouette Dodge showed during Stellantis' 2021 EV Day.   Inside, the Italian brand's crest in the steering wheel center cap is replaced by Dodge's twin slashes, and the steering wheel has been stripped of the large, curved paddle shifters the Tonale showed on its debut. There's still a start/stop button on the steering wheel, but where the Tonale has a driving mode dial on its dash, this supposed Hornet has another start/stop button. Dodge's push-to-start buttons are usually on the instrument panel, so our guess is that the wheel is a holdover for testing. On the center tunnel, the parking alert buttons and Italian Tricolore flag on the Alfa Romeo are replaced by three different buttons.   We've known Dodge has two electrified vehicles on the way, and the Hornet name has been low-key buzzing for two years. Fiat Chrysler applied to trademark the name in the U.S. in March 2020; at the time, it was thought a vehicle with that name could replace the Journey. In 2021, a July rumor out of Italy was the first whisper of the Hornet name being attached to the Alfa Romeo Tonale. In August, when Stellantis CEO Carlos Tavares said Dodge would get a PHEV in 2024, watchers pegged that model as the Hornet. That hybrid powertrain would show a year after the vehicle's launch, the Hornet anticipated as a 2023 model with the Tonale's turbocharged 2.0-liter four-cylinder. That engine could get the same 256 horsepower and 295 pound-feet of torque as the Tonale, or be boosted to satisfy Dodge's performance credentials.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Chrysler recalls small number of 2013-2014 cars and trucks over engine debris

Chrysler is recalling a small number cars over issues with their 2.4-liter four-cylinder engines. The recall, which affects 522 examples of its 2013 Dodge Avenger and Chrysler 200 models, as well as 2014 Jeep Compass and Patriot CUVs has to do with potential debris in the balance shaft bearings.
The abrasive stuff can cause the oil pressure to drop, which could lead to the engine stalling or outright failure. This situation could at best leave drivers stranded and at worst lead to a crash.
Chrysler will begin notifying owners, who will need to report in to have the balance shaft module replaced. All repairs are naturally free of charge. Scroll down for the bulletin from NHTSA.