1953 Dodge Job Rated Pickup Truck on 2040-cars

Auto blog

VLF Force 1 V10 is a rebodied Viper priced like a Lamborghini

It would appear that Henrik Fisker is done with hybrids. His latest project, called the Force 1, packs an oversized V10 engine with no electric assist in sight and all the environmental credentials of a herd of flatulent cattle. Alongside the Karma-based, Corvette-powered Destino, the Force 1 is the second product from VLF Automotive. Fisker has taken partnership in the new firm as chief designer alongside chairman Bob Lutz and CEO Gilbert Villarreal. The company isn't saying explicitly what the Force 1 is based on, but it doesn't take a CSI team to trace its roots back to the Dodge Viper. Never mind that it's being built in Auburn Hills – the same Detroit suburb where Chrysler is headquartered – or that it was jointly developed by Fisker and professional Viper racer and dealer Ben Keating. It also happens to be powered by an 8.4-liter V10, and there aren't many of those kicking around the industry. Instead of the Viper's 645 horsepower and 600 pound-feet of torque, the Force 1's ten-cylinder engine is optimized to deliver 745 hp and 638 lb-ft. That, according to VLF, is enough to send the coupe rocketing to 60 in 3.0 seconds flat, covering the quarter-mile in under 11 seconds on its way to a top speed of 218 miles per hour. The power is transmitted to the Pirelli PZero rubber through a six-speed manual, but VLF says it will fit it with an automatic at the customer's request. Around that massive engine and two-seat cockpit, Fisker designed a new shape that, for better or for worse, looks way more aggressive than the Viper's. The Force 1's proportions are tellingly super-snake, but the curves are replaced by some very angry-looking angles and vents. Its head- and taillights are ultra thin, and the deep-dish, split-four-spoke wheels seem to visually split the difference between the three-spoke wheels on the original Viper and the five-spoke alloys it wears today. If you doubted the Force 1's origins before, the interior ought to give it away, with its wide tunnel and familiar surfaces. Only VLF has refinished it in leather, suede, and Alcantara, all diamond stitched with contrasting thread to help position this as a more luxurious prospect than the Dodge. It even fit between the seatbacks place for two champagne bottles that we hope nobody would consider consuming before trying to handle that much power. Of course, none of this will come cheap.

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

Junkyard Gem: This 1987 Dodge 600 SE Sedan is suspiciously Benz-ish

The K Platform, introduced for the 1981 model year, saved Chrysler from certain bankruptcy. By 1983, a stretched-out K chassis had been developed; the Chrysler version was the E-Class, while Dodge had the 600. These cars have become all but extinct now, so this '87 600 sedan in a Denver-area wrecking yard is a noteworthy Junkyard Gem. Ford explicitly compared the appearance of the late-1970s Granada to that of the Mercedes-Benz W123 in their advertising, and so the ground was broken for Chrysler to make the allusions to Stuttgart machinery even more obvious a few years later. The name of the Chrysler E-Class was about as subtle as a tire iron blow to the kidneys, and the badging on its Dodge 600 sibling left little to the imagination. 600s came from the factory with several variations of the Chrysler 2.2/2.5 engine, as well as the Mitsubishi "Hemi 2.6" four-cylinder. This car has the 2.5 Chrysler engine, rated at 97 horsepower. Base price was $10,553, about $23,500 in 2017 dollars (the cheapest new Mercedes-Benz E-Class cost $38,600 in 1987, so there wasn't much customer overlap between the two cars). The 600s weren't bad cars for the price, though the build quality wasn't quite up to Mercedes-Benz standards. You'll find this thumbtack treatment on most K-Car headliners that still drive today. The interior is all tan and brown, with plenty of tough industro-velour upholstery and not-so-convincing artificial wood. Aluminum-faced home audio equipment was all the rage during the 1980s, and the trend spread to automotive controls. No cassette in this car, but at least it had AM and FM radio (even plain old mono AM radios were still expensive options on many cars as late as 1987, so the standard AM/FM stereo rig in the 600 was an attractive deal). This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. You can't beat the 600!