2004 Dodge Neon Sxt Sedan 4-door 2.0l on 2040-cars

Auto blog

VLF Force 1 V10 is a rebodied Viper priced like a Lamborghini

It would appear that Henrik Fisker is done with hybrids. His latest project, called the Force 1, packs an oversized V10 engine with no electric assist in sight and all the environmental credentials of a herd of flatulent cattle. Alongside the Karma-based, Corvette-powered Destino, the Force 1 is the second product from VLF Automotive. Fisker has taken partnership in the new firm as chief designer alongside chairman Bob Lutz and CEO Gilbert Villarreal. The company isn't saying explicitly what the Force 1 is based on, but it doesn't take a CSI team to trace its roots back to the Dodge Viper. Never mind that it's being built in Auburn Hills – the same Detroit suburb where Chrysler is headquartered – or that it was jointly developed by Fisker and professional Viper racer and dealer Ben Keating. It also happens to be powered by an 8.4-liter V10, and there aren't many of those kicking around the industry. Instead of the Viper's 645 horsepower and 600 pound-feet of torque, the Force 1's ten-cylinder engine is optimized to deliver 745 hp and 638 lb-ft. That, according to VLF, is enough to send the coupe rocketing to 60 in 3.0 seconds flat, covering the quarter-mile in under 11 seconds on its way to a top speed of 218 miles per hour. The power is transmitted to the Pirelli PZero rubber through a six-speed manual, but VLF says it will fit it with an automatic at the customer's request. Around that massive engine and two-seat cockpit, Fisker designed a new shape that, for better or for worse, looks way more aggressive than the Viper's. The Force 1's proportions are tellingly super-snake, but the curves are replaced by some very angry-looking angles and vents. Its head- and taillights are ultra thin, and the deep-dish, split-four-spoke wheels seem to visually split the difference between the three-spoke wheels on the original Viper and the five-spoke alloys it wears today. If you doubted the Force 1's origins before, the interior ought to give it away, with its wide tunnel and familiar surfaces. Only VLF has refinished it in leather, suede, and Alcantara, all diamond stitched with contrasting thread to help position this as a more luxurious prospect than the Dodge. It even fit between the seatbacks place for two champagne bottles that we hope nobody would consider consuming before trying to handle that much power. Of course, none of this will come cheap.

Towing with the 2016 Ram lineup [w/video]

I do not tow things. Ever. Yet I recently found myself at the Fiat Chrysler Automobiles proving grounds in Chelsea, MI, where I'd be testing the hauling capabilities of Ram's current product range. This experience was not only a perfect education for a towing novice like me, but allowed me to tow far more weight than I'd ever consider hauling the real world, and all within the safe confines of the Chelsea Proving Grounds. There was an extremely diverse array of vehicles at my disposal, including Ram's gasoline- and diesel-powered offerings with trucks ranging from the 1500 on up through the 5500 Chassis Cab, as well ProMaster vans. Beyond that, FCA brought out a number of vintage Dodge pickups for me to play with, while also working with Case IH to provide a track-loader I could test. I put together a range of videos covering everything from the classics to the production trucks to the construction equipment. And despite some technical difficulties – you'll notice a distinct lack of in-car videos, with blame going to a corrupted micro SD card – I've assembled ten videos that give an up-close look at Ram's offerings. 2015 Ram ProMaster City Let's start small. The ProMaster City only has a towing capacity of 2,000 pounds. That's a reasonably impressive figure for a van that uses the same powertrain as a Chrysler 200. The 2.4-liter four-cylinder and nine-speed automatic weren't really bothered with the extra weight added by the trailer. Even when accelerating at freeway speeds, the ProMaster City didn't feel out of breath or hampered by its load. That said, the rear of the van was unloaded, which probably wouldn't be the case for most consumers. It's unclear how the City would feel if its driver were taking advantage of the max payload (1,883 pounds) and towing. 2015 Ram ProMaster 1500 To be polite, the Ram ProMaster is a difficult vehicle to like. Its awkward seating position is bus-like and lacks the visibility enjoyed by the Ford Transit or the utter driving comfort of the Mercedes-Benz Sprinter. Its 3.0-liter, four-cylinder turbodiesel engine, meanwhile, is something of an anomaly. While it's potent for a four-cylinder diesel, producing 295 pound-feet of torque and 174 horsepower, those numbers don't feel all that impressive when loaded down. The model I tested was barely using half of its 5,100-pound maximum towing weight and was loaded down with just 500 of its 3,620-pound payload. Yet it lacked the pluckiness of the smaller City.

FCA to invest $4.5B for new Detroit plant, expanded production at current facilities

We expected some shifts in manufacturing plans as Fiat Chrysler plans to begin electrifying its Jeep brand, but this news bodes well for Michigan. FCA announced today that it would spend $4.5 billion to expand production in the state, including building a new assembly plant in Detroit and increasing capacity at five other facilities in the state. The plan, which FCA says will create nearly 6,500 new jobs, will help to meet increasing demand for Ram and Jeep products, and to electrify Jeep models. $1.6 billion will be set aside to transform the Mack Avenue Engine Complex into a site to build the next generation of Jeep Grand Cherokee, as well as an unspecified, new three-row Jeep model. FCA says this part of the plan will create 3,850 new jobs. FCA is increasing its investment in the Warren Truck plant to $1.5 billion in order to continue building the Ram 1500 Classic, as well as the new Jeep Wagoneer and Grand Wagoneer, creating 1,400 new jobs. FCA says that the new Ram 1500 Heavy Duty will still be built in Saltillo, Mexico. At FCA's Jefferson North facility, the automaker will invest $900 million to upgrade the plant. This site will continue to build the Dodge Durango, as well help build the next Jeep Grand Cherokee. FCA expects this to create 1,100 new jobs. As Jeep plans to electrify models in its SUV lineup, each of the above plants will produce plug-in hybrid versions of the Jeep models produced there, "with flexibility to build fully battery-electric models in the future," the company said in its announcement. "Three years ago, FCA set a course to grow our profitability based on the strength of the Jeep and Ram brands by realigning our U.S. manufacturing operations," said FCA CEO Mike Manley, referring in part to earlier investments in Illinois, Ohio and Michigan. "Today's announcement represents the next step in that strategy," Manley continued. "It allows Jeep to enter two white space segments that offer significant margin opportunities and will enable new electrified Jeep products, including at least four plug-in hybrid vehicles and the flexibility to produce fully battery-electric vehicles." Other investments include $119 million to move production of the 3.0-, 3.2- and 3.6-liter Pentastar engines from Mack I to the Dundee Engine Plant, and $400 million for increased capacity and 80 new jobs at the Sterling and Warren stamping plants. This comes at a time when FCA's U.S.