2007 Dodge Magnum Sxt on 2040-cars

Auto blog

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

Dodge Scat Pack for 5.7L Hemi V8 detailed, priced

Dodge revived the Scat Pack name back in November at the 2013 SEMA show. At the time, though, we were short of details on forthcoming upgrade packages, which were destined to add some oomph to the Challenger, Charger and Dart. We're still waiting to hear about the upgrades to the Dart's 2.4-liter four-pot, but Dodge has gone ahead and released the details on the upgrades to the 5.7-liter Hemi V8 in the Challenger and Charger R/T.
As we detailed in our original post, three different Scat Packs will be available that will allow customers to upgrade their cars without voiding the warranties. Starting with the $2,195 Stage 1 kit, owners will net an extra 18 horsepower and 18 pound-feet of torque thanks to a Mopar-branded cold-air intake, exhaust and ECU ref lash. Stage 1 is also the only package that could be installed outside of a Chrysler-authorized service center without voiding the warranty (a mechanically competent owner could even do it at home, we're told by Dodge). Stage 2 builds on the entry level Scat Pack, and adds performance camshaft kit, which boosts output over the stock 5.7 by up to 30 hp for $1,895. As with the Stage 1, the ECU is tweaked.
For those that want to go whole hog, they can add the Stage 3 for $4,995. The top-tier gets quite serious, adding CNC-ported cylinder heads, as well as high-flow headers and cats. Output over stock is 58 hp and 47 lb-ft of torque. Each kit comes with a pair of badges, just in case owners want a bit of visual flair.

Roadkill builds crazy-cheap 1968 Dodge Charger rat rod using an old motorhome

Certain requests for description simply cannot be fulfilled, like if someone asked you to describe Picasso's Guernica or Gilliam's Brazil. There is only one appropriate answer to such entreaties, and that is: "You just gotta see it." That's where we are with the latest episode of Roadkill, wherein Messr's Freiburger and Finnegan dig out a 1968 Dodge Charger that Freiburger acquired in exchange for a set of cylinder heads, and intend to stuff it with the big-block motor from a long-bed, three-quarter ton Dodge pickup.
Only the pickup is too nice to tear apart, and the Charger needs a whole lot more lovin' - and parts - than initially expected. Enter, stage right, the Class A Dodge Pace Arrow motorhome with a 440 big-block purchased for $1,000, and a retired Plymouth Fury from a previous episode.
What ensues over the course of the 40-minute installment is more cuttin', yankin', leakin', stallin', hammerin' and smokin' action than you've seen in a long time, and some techniques that would have made even Cooter wonder, "I'm not sure if we should do that." By the end, though, the payoff is good enough to make you think about perusing AutoTrader for a '68 Charger just to see if maybe...