Sxt 3.5l Traction Control - Abs And Driveline Rear Defogger Power Heated Mirrors on 2040-cars

Auto blog

Watch these Dodge Demons explode on a Texas drag strip

The Dodge Challenger SRT Demon is extremely quick. It can hit 60 mph from a dead stop in less time than it takes to read this sentence thanks to its supercharged 6.2-liter V8. That engine makes up to 840 horsepower and 770 pound-feet of torque, depending on what octane is running through the fuel lines. That's a ton of power going solely to the rear wheels. So much so that Dodge developed a number of features and a new set of tires specifically for the car. In our time with the Demon, the car took abuse run after run on a drag strip without skipping a beat, but it seems some actual owners aren't quite so lucky. Just take a look at what happened to a few of these cars. You can see the whole car shake and jitter right as the whole rear explodes in front of the tree. It seems the initial shock from the launch — the most taxing bit of any drag run — is what kills the differentials. Catastrophic failure is rarely pretty, but it is neat to see the whole thing occur in slow motion. Three more cars — four stock and one modified in total — suffered similar fates. Not a great look for Dodge or SRT. According to The Drive, a private drag event in Texas drew a number of Demon owners all trying to beat NHRA NHRA Top Fuel racer Leah Pritchett's time in her personal Dodge Demon — 42 stock Demons attended along with five modified cars. While no one managed to match her 9.65-second quarter-mile run, a few owners did dip below 10 seconds. Now, there are a few of caveats we must address. First, with any modified car, you run the risk of breaking something, even with a car that's set up from stock specifically for drag strips. Even a set of tires like the Mickey Thompsons shown in the video above can have an effect on driveline components. Horsepower may be king, but it's torque that's the rear killer. All that torque sends a shock through the car. Adding even more with aftermarket parts increases the risk of something failing. The modified car was apparently pushing out about 1,000 horsepower. That said, four of the five vehicles were stock, so any extra power or torque should theoretically be a non-factor. The drag strip's surface was maintained by a company called Mass Traction. FCA used Mass Traction during the Demon's development, so that too should be a non-factor in the part's failure. It's unclear what exactly caused the failures, though The Drive reports that FCA officials are investigating the matter. Related Video: This content is hosted by a third party.

FCA recalls 15k Grand Cherokees, Durangos over brake issues

The Basics: Fiat Chrysler Automobiles is recalling 14,768 examples of the Jeep Grand Cherokee and Dodge Durango, both from the 2015 and 2016 model years, and built between December 9, 2015, and January 14, 2016. The Problem: The left front brake caliper on some vehicles may have been made from the wrong type of iron, and could be prone to crack. A cracked brake caliper may not function properly. Injuries/Deaths: None reported. The problem was discovered by the automaker during testing. The fix: Dealers will need to check the casting date of the component in question, and if necessary, replace the brake caliper. The schedule for carrying out the recall service has yet to be outlined. If you own one: Expect to hear from the manufacturer to arrange an appointment with your local dealer. Related Video: RECALL Subject : Front Left Brake Caliper May Break Report Receipt Date: MAR 23, 2016 NHTSA Campaign Number: 16V168000 Component(s): SERVICE BRAKES, HYDRAULIC Potential Number of Units Affected: 14,768 Manufacturer: Chrysler (FCA US LLC) SUMMARY: Chrysler (FCA US LLC) is recalling certain model year 2015-2016 Jeep Grand Cherokee and Dodge Durango vehicles manufactured December 9, 2015, to January 14, 2016. In the affected vehicles, the left front brake caliper may crack due to being made from an incorrect material. CONSEQUENCE: A cracked brake caliper may lengthen the distance needed to stop the vehicle and increase the risk of a crash. REMEDY: Chrysler will notify owners, and dealers will inspect the front left brake caliper and depending on its casting date, replace it, free of charge. The manufacturer has not yet provided a notification schedule. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S16. NOTES: Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.

Dodge Viper plant will close for good Aug. 31

It has been a long time coming, an end rumored since at least 2015, but after 25 years, the Dodge Viper's demise is nigh. Production of the $90,000 bespoke sports car is ending. Therefore, FCA will be shutting down its Conner Assembly Plant on Aug. 31. Automotive News reports that the Detroit plant will be shutting down. The car has been hand-built there since 1995, save for a hiatus in 2010-13 (production began at FCA's Mack Plant in 1992). The Prowler was built there, too, from 1997 to 2002. More than 80 workers currently build the Viper, making Conner FCA's smallest assembly facility. But not many Vipers are sold - 630 last year - despite an enthusiastic following. And of course FCA's own 707-horsepower Dodge Challenger and Charger SRT Hellcats and new 840-horsepower Challenger SRT Demon can't help matters. But the last straw is the fact the Viper can't comply with new safety requirements going into effect. On the bright side, the UAW has seen the plant closure coming since 2015, and FCA has told the state of Michigan that it expects to find positions at other plants for the Viper crew. FCA has been celebrating the Viper valedictory for a couple of years now, offering serialized special editions, including the $121,000 Viper ACR, and touting the ability to build unique Vipers with its "1 of 1" customization program, with a choice of 16,000 unique paint colors and 48,000 unique stripe combinations. Related Video: