2024 Dodge Hornet Gt Plus Awd on 2040-cars

Auto blog

2015 Dodge Challenger SRT Hellcat [w/videos]

Darrell Waltrip once said, "If the lion didn't bite the tamer every once in a while, it wouldn't be exciting." The sentiment behind that aphorism is causing my adrenal gland to wake up as Dodge and SRT drivers and engineers - somber-faced to a man - give me the track talk that will precede my driving the 2015 Dodge Challenger SRT on the circuit at Portland International Raceway. PIR might not be Daytona, and the 707-horsepower Challenger Hellcat might seem tame to a legend like ol' Jaws, but there's a not-small part of me that's thinking about how hard Dodge's fire-breathing kitty might bite.
Just a few hours previous, I'd gotten behind the wheel of the Hellcat for the first time, letting its hyperbole-spitting, supercharged V8 Hemi pull me yieldingly through Portland's morning commuter traffic. Lulled into a cocky certainty by the Challenger's good manners at low speed, I drove the throttle just a hair too deep, too fast when I ran on to the highway ramp. For just an instant the rear tires were utterly drenched in torque, and the back end of the big Dodge loosened up like a drift car on a wet track. Throttle steer lives at the fleeting whim of your right foot in this car.
It was no big thing to lay off the gas and pull the Hellcat back in line as I entered the highway, but the incident did get me to thinking: What will this car do to me on a road course?

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

How to tune a car right: Part 3, tuning Mopar with OST Dyno

Not long ago, I wrote a story about a pony car tuned with a supercharger. The blower install had been done properly. Then the car's owner bolted on a set of great looking wheels wrapped in good looking but inexpensive rubber. On my first test drive, I couldn't get any of that supercharged sweetness to the ground. It was the perfect ride for parking in a Burger King parking lot on a Friday night. I tooled around on a Sunday drive, shaking my head that someone had spent five figures to get more power the right way, with a clean install, then wiped out the gains so thoroughly that the stock engine would likely have overwhelmed the tires. This got me thinking about the ways people ruin their quest for horsepower, either on the front end by not insisting on a clean install and paying the money for it, or on the back end with supplemental purchases like cheap tires or cheap gas. So I called three tuners, one focused on GM, one on Mopar, one on Ford, to find out what people should know about how to get the best power for their goals, and how to make sure they are able to use all that power. The first interview in this three-part series was with Blake Leonard at Top Speed Cincy in Cincinnati, Ohio, the second with Brandon Alsept at BA Motorsports in Milford, Ohio. This third and last interview is with Micah Doban at OST Dyno in Slippery Rock, Pennsylvania, a family business with more than 40 years of Mopar expertise specializing in Gen III Hemis, but tuning everything from land-speed cars and drag racers to Jeeps The interview has been edited for clarity and concision. Do people who come to OST generally know what they want? Probably 80% of the people who come in simply want more power with no particular ET goal [ET is a kind of bracket handicapped drag racing – ed.]. WhatÂ’s the best way to start a Mopar tune? The first thing is what people often skip, and that's to find a tuner or a shop. People will throw parts on their cars that the Internet said to, then go to a tuner who does things a different way, and [the tuner is] like ‘No we don't like to use these injectors, we don't like these parts.Â’ You have to find someone familiar with the parts that are on your car or that you're planning to put on your car. So having a goal and then finding a tuner who can help you with that goal is proper way to start. Exactly. And a lot of tuners have their own formula – and when I say tuner I mean someone that also does work to the cars.