2018 Dodge Grand Caravan Sxt Mobility Handicap Van Handicap on 2040-cars

Auto blog

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

Dodge Durango Shaker concept: A 392 V8 in front of six Viper seats

When done right, a parts-bin special can be a beautiful thing. This Dodge Durango Shaker concept for the 2016 SEMA show is one such vehicle, and it's easily our favorite Mopar debuting in Vegas. The key, of course, is pulling from the right bins. Take a tour and you'll see Charger, Challenger, and Viper pieces grafted onto this slick crossover. The featured special part is the big, 6.4-liter 392 Hemi V8 that's been dropped under the hood; it's sourced from the SRT Challenger and Charger where it makes 485 horsepower and 475 pound-feet of torque. With that in place, the fabricators cut a big hole in that hood for the Challenger's awesome optional shaker scoop. It wasn't an easy installation; it required a custom spacer for the intake to make sure everything lined up with the hole properly. View 17 Photos Apparently there were some Viper seats lying around, so six of them were stuck into this Durango. Makes sense. It does lose a bit of people-carrying capability as a result, since only two seats fit in each row, and the seats don't fold for extra cargo room. A Dodge spokesperson attested to the fact that all three rows are usable, if not totally comfortable. But then stock third-row seats aren't always that comfortable anyway. Seriously, though, Viper seats. We don't care how comfortable or usable the result is. Although you might not give it a second thought, even the fuel filler needed some special attention. This piece was also lifted from a Dodge Challenger, and it was taken along with the surrounding sheet metal. Because of the different orientation of the filler cover on the Challenger, the builders decided the easiest way to get it to fit was to chop the fuel filler section out and weld it onto the Durango. The designers also put a little blue Stig on the cover. And those are just the cool parts that were hard to install. This Durango features plenty of other slick details, like the custom bumpers, fender flares, and side skirts. Everything is painted B5 Blue with matte black and carbon accents all around. Up front, the bumper hides a pair of fog lights stolen from a Challenger Hellcat – and yes, they're the ones with intakes in the middle. The grille is also a custom piece, losing the standard crosshair design for better airflow. The fender flares cover up some seriously wide, 305-section tires at all four corners, which are hauled down by Hellcat brakes. The rear bumper bumper contains a stylish center-exit exhaust with dual tips.

FCA's large, LX-based RWD cars will stick around until 2020

Fiat Chrysler Automobiles plans to stick with the Dodge Challenger, Dodge Charger, and Chrysler 300 until at least 2020, reports Automotive News. The information comes from two unnamed sources and was loosely confirmed by details in the automaker's new labor contract with Unifor, Canada's auto union. The plan, according to two anonymous sources, is to lightly refresh the Challenger, Charger, and 300 until the vehicles make the switch to FCA's new Giorgio platform. The refresh, as Automotive News points out, will happen in 2018. The Giorgio platform currently underpins the Alfa Romeo Giulia and is expected to find its way to two of the three large American vehicles for the 2021 model year. At that time, FCA will discontinue either the Charger or the 300, claim AN's unnamed sources. If one of the vehicles were to go, it would most likely be the 300. The 300's LX platform would be approximately 15 years old in 2020 and the vehicle doesn't draw in as many sales as the Challenger or the Charger. The Charger made the switch from the LX platform in 2010 with the current model utilizing the mildly updated LD platform, while the Challenger recently moved from the LC platform to the LA platform last year. All of those rear-wheel-drive platforms are closely related. Automotive News points out that FCA CEO Sergio Marchionne stated that the new platform could be utilized across various applications in a conference call with analysts last month. The plan, according to the report, is to stretch and widen the Giorgio platform for the next-gen Challenger and Charger. The new platform is also rigid enough to allow the automaker to add a convertible to its lineup, which could lend further credence to rumors of an upcoming Barracuda. Hopefully, the move to the new Giorgio platform doesn't delay the all-wheel-drive Challenger GT AWD or the wide-body, Hellcat-powered Challenger ADR. We'll just have to wait and see. Related Video: News Source: Automotive News - sub. req. Chrysler Dodge Coupe Performance Sedan FCA fiat chrysler automobiles