2005 Dodge Grand Caravan Wheelchair Van on 2040-cars

Auto blog

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

Dodge Charger SRT Hellcat in the works

In Autoblog's recent First Drive of the 2015 Challenger SRT with the 707-horsepower Hellcat V8 we found its engine to be as brutally powerful as the numbers would suggest, even if it wasn't the best handler. However, the muscle-car-styling just isn't right for some buyers that need four doors and proper rear seats to haul around the family. It appears that Dodge has their backs, though, because the Hellcat is very likely on its way into the Charger in the near future. Imagine the looks on your passengers' faces when you stomp down on the throttle.
According to Road and Track, when Dodge submitted the Hellcat for engine power certification to the Society of Automotive Engineers, the company included the Charger on the paperwork. That showed that the automaker wanted the engine checked out for the sedan, too. R&T reckons the 707-hp Charger would hit the road about a year from now, clearing the Challenger for a year of exclusivity with the powerplant.
When the Charger SRT Hellcat does hit the road, it may carry a very special accolade. Assuming nothing beats it in the meantime, it might be the world's highest horsepower production sedan. Think on that for a second. Even a Mercedes S65 AMG only has 621 horsepower, though a good bit more torque at 738 pound-feet to the Dodge's 650 lb-ft. So while the beastly engine is getting put into other models, where else would you like to see it? The Ram? Grand Cherokee? Let us know in Comments.

Chrysler investing $20M in Toledo plant to support 9-speed auto production

In 2011, Chrysler announced a $72-million investment in its Toledo Machining Plant to modernize production of the eight- and nine-speed torque-converters for automatic transmissions made there. That upgrade work won't be finished until Q3 of this year, but Chrysler has already announced a further $19.6-million investment to increase production capacity for the nine-speeders.
The extra units will be necessary because the nine-speed transmission they'll be mated to is going into three popular models: it will debut on the 2014 Jeep Cherokee, then go into the Chrysler 200 and Dodge Dart. The company predicted that this year alone it would sell 200,000 units equipped with the nine-speed tranny, and it is spending some $374 million in addition to the investment in Toledo to upgrade production capacity for it.
The work attached to this new investment won't begin until Q3 of 2014, and it will be finished by the end of that year. There's a press release below with all the details.