69k Original Miles, Build Sheet, Stripe Package, Cold A/c, Cragar Ss Wheels !! on 2040-cars

Auto blog

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

2015 Dodge Challenger SRT Hellcat [w/videos]

Darrell Waltrip once said, "If the lion didn't bite the tamer every once in a while, it wouldn't be exciting." The sentiment behind that aphorism is causing my adrenal gland to wake up as Dodge and SRT drivers and engineers - somber-faced to a man - give me the track talk that will precede my driving the 2015 Dodge Challenger SRT on the circuit at Portland International Raceway. PIR might not be Daytona, and the 707-horsepower Challenger Hellcat might seem tame to a legend like ol' Jaws, but there's a not-small part of me that's thinking about how hard Dodge's fire-breathing kitty might bite.
Just a few hours previous, I'd gotten behind the wheel of the Hellcat for the first time, letting its hyperbole-spitting, supercharged V8 Hemi pull me yieldingly through Portland's morning commuter traffic. Lulled into a cocky certainty by the Challenger's good manners at low speed, I drove the throttle just a hair too deep, too fast when I ran on to the highway ramp. For just an instant the rear tires were utterly drenched in torque, and the back end of the big Dodge loosened up like a drift car on a wet track. Throttle steer lives at the fleeting whim of your right foot in this car.
It was no big thing to lay off the gas and pull the Hellcat back in line as I entered the highway, but the incident did get me to thinking: What will this car do to me on a road course?

Lee Iacocca's very first Dodge Viper RT/10 nets $285,500 at auction

The first 1992 Dodge Viper RT/10 to roll down the assembly line, which was snapped up by Chrysler chief Lee Iacocca, yesterday hammered at the Bonhams auction in Arizona for $285,500, more than double the pre-sale estimate. According to a history of the car published by the auction house, Iacocca, in his introduction of the Viper to the press, pointed to the car on stage and said, "This one right here is mine." That historic Viper, with serial number 001, has never been available on the open market, as Iacocca kept the car from new until he passed away last year. The car has been driven just 6,200 miles and was being sold by his estate. Other Lee Iacocca cars offered at the same sale fared less well. A 1986 Chrysler LeBaron Town & Country convertible — the ultimate expression of Iacocca's company-saving K-cars — with 20,500 miles on it sold for $19,040. That's less than the $20,000 to $25,000 the auction house had estimated the car would bring. A third car from the former auto executive's estate was a customized 2009 Ford Mustang. The pony car was one of a limited run of 45 Iacocca-branded custom Mustangs, which were reworked by Metalcrafters and sold by Galpin Ford in Los Angeles. The Iacocca Mustang, never titled and with 220 miles on it, hammered for $49,280. Related Video:     Featured Gallery Lee Iacocca's 1992 Dodge Viper RT/10 View 13 Photos Celebrities Chrysler Dodge Auctions Automotive History