2014 Dodge Dart Aero on 2040-cars

Auto blog

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

Dodge Charger SRT Hellcat in the works

In Autoblog's recent First Drive of the 2015 Challenger SRT with the 707-horsepower Hellcat V8 we found its engine to be as brutally powerful as the numbers would suggest, even if it wasn't the best handler. However, the muscle-car-styling just isn't right for some buyers that need four doors and proper rear seats to haul around the family. It appears that Dodge has their backs, though, because the Hellcat is very likely on its way into the Charger in the near future. Imagine the looks on your passengers' faces when you stomp down on the throttle.
According to Road and Track, when Dodge submitted the Hellcat for engine power certification to the Society of Automotive Engineers, the company included the Charger on the paperwork. That showed that the automaker wanted the engine checked out for the sedan, too. R&T reckons the 707-hp Charger would hit the road about a year from now, clearing the Challenger for a year of exclusivity with the powerplant.
When the Charger SRT Hellcat does hit the road, it may carry a very special accolade. Assuming nothing beats it in the meantime, it might be the world's highest horsepower production sedan. Think on that for a second. Even a Mercedes S65 AMG only has 621 horsepower, though a good bit more torque at 738 pound-feet to the Dodge's 650 lb-ft. So while the beastly engine is getting put into other models, where else would you like to see it? The Ram? Grand Cherokee? Let us know in Comments.

7 major automakers to build open EV charging network

A new joint venture established by BMW, GM, Honda, Hyundai, Kia, Mercedes-Benz and Stellantis will build a new North American electric vehicle charging network on a scale designed to compete with Tesla's industry-benchmark Supercharger network. The 30,000-plus planned new chargers will accommodate both Tesla's almost-standard North American Charging System (NACS) and existing automakers' Combined Charging System (CCS) options, effectively guaranteeing compatibility with the vast majority of current and upcoming electric models — whether they're from one of the involved automakers or not.  "With the generational investments in public charging being implemented on the Federal and State level, the joint venture will leverage public and private funds to accelerate the installation of high-powered charging for customers. The new charging stations will be accessible to all battery-powered electric vehicles from any automaker using Combined Charging System (CCS) or North American Charging Standard (NACS) and are expected to meet or exceed the spirit and requirements of the U.S. National Electric Vehicle Infrastructure (NEVI) program." Critically, the automakers involved will have a say in how the charging tech is implemented, guaranteeing that the hardware will play nicely with each automaker's in-house charging systems. Hyundai and Kia, for example, were hesitant to jump on board the Tesla NACS bandwagon earlier this year over concerns that the Supercharger network is insufficient for powering the two automakers' 800-volt charging systems; similar tech is used by Volkswagen and Porsche.  In addition to providing much-needed capacity and high-output charging for America's growing fleet of electric cars and trucks, the new network will integrate seamlessly with each automaker's in-app and in-vehicle features, rather than forcing customers to use third-party tools and payment systems, as is the case with some existing public charging infrastructure.  "The functions and services of the network will allow for seamless integration with participating automakersÂ’ in-vehicle and in-app experiences, including reservations, intelligent route planning and navigation, payment applications, transparent energy management and more. In addition, the network will leverage Plug & Charge technology to further enhance the customer experience," the announcement said.