1966 Dodge Coronet 440 on 2040-cars

Auto blog

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

Towing with the 2016 Ram lineup [w/video]

I do not tow things. Ever. Yet I recently found myself at the Fiat Chrysler Automobiles proving grounds in Chelsea, MI, where I'd be testing the hauling capabilities of Ram's current product range. This experience was not only a perfect education for a towing novice like me, but allowed me to tow far more weight than I'd ever consider hauling the real world, and all within the safe confines of the Chelsea Proving Grounds. There was an extremely diverse array of vehicles at my disposal, including Ram's gasoline- and diesel-powered offerings with trucks ranging from the 1500 on up through the 5500 Chassis Cab, as well ProMaster vans. Beyond that, FCA brought out a number of vintage Dodge pickups for me to play with, while also working with Case IH to provide a track-loader I could test. I put together a range of videos covering everything from the classics to the production trucks to the construction equipment. And despite some technical difficulties – you'll notice a distinct lack of in-car videos, with blame going to a corrupted micro SD card – I've assembled ten videos that give an up-close look at Ram's offerings. 2015 Ram ProMaster City Let's start small. The ProMaster City only has a towing capacity of 2,000 pounds. That's a reasonably impressive figure for a van that uses the same powertrain as a Chrysler 200. The 2.4-liter four-cylinder and nine-speed automatic weren't really bothered with the extra weight added by the trailer. Even when accelerating at freeway speeds, the ProMaster City didn't feel out of breath or hampered by its load. That said, the rear of the van was unloaded, which probably wouldn't be the case for most consumers. It's unclear how the City would feel if its driver were taking advantage of the max payload (1,883 pounds) and towing. 2015 Ram ProMaster 1500 To be polite, the Ram ProMaster is a difficult vehicle to like. Its awkward seating position is bus-like and lacks the visibility enjoyed by the Ford Transit or the utter driving comfort of the Mercedes-Benz Sprinter. Its 3.0-liter, four-cylinder turbodiesel engine, meanwhile, is something of an anomaly. While it's potent for a four-cylinder diesel, producing 295 pound-feet of torque and 174 horsepower, those numbers don't feel all that impressive when loaded down. The model I tested was barely using half of its 5,100-pound maximum towing weight and was loaded down with just 500 of its 3,620-pound payload. Yet it lacked the pluckiness of the smaller City.

2015 Dodge Charger configurator opens up shop

Itching to get your hands on a new 2015 Dodge Charger? Your day is almost nigh, my friend While you're waiting, you can spec out how you'd want your muscle sedan to look as Dodge has included the revised four-door in its online configuration tool. Though it's not the most impressive or interactive of configurators we've seen, the site lets you choose any color you want (from the limited array available anyway) along with all the key options packages and such. First you'll need to choose a trim level though, but we're afraid the Hellcat version isn't part of this site, and the SRT site hasn't launched a configurator yet for the world's fastest production sedan, so you'll have to choose between SE, SXT and R/T trim levels. Related Video: