2019 Dodge Charger Sxt 4dr Sedan on 2040-cars

Auto blog

Chrysler investing $20M in Toledo plant to support 9-speed auto production

In 2011, Chrysler announced a $72-million investment in its Toledo Machining Plant to modernize production of the eight- and nine-speed torque-converters for automatic transmissions made there. That upgrade work won't be finished until Q3 of this year, but Chrysler has already announced a further $19.6-million investment to increase production capacity for the nine-speeders.
The extra units will be necessary because the nine-speed transmission they'll be mated to is going into three popular models: it will debut on the 2014 Jeep Cherokee, then go into the Chrysler 200 and Dodge Dart. The company predicted that this year alone it would sell 200,000 units equipped with the nine-speed tranny, and it is spending some $374 million in addition to the investment in Toledo to upgrade production capacity for it.
The work attached to this new investment won't begin until Q3 of 2014, and it will be finished by the end of that year. There's a press release below with all the details.

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

NC dealer creates the convertible Challenger that Dodge won't build

Dodge still hasn't turned the Challenger into a convertible, and the odds of seeing a factory-built drop-top muscle car appear in showrooms are decreasing annually. Tired of waiting, a dealership in North Carolina teamed up with a Florida-based body shop to create a topless alternative to the Ford Mustang and the Chevrolet Camaro. It's the real thing, and it's for sale. Keffer Dodge, Chrysler, Ram and Jeep shipped three 2019 Challengers to a shop named Convertible Builders, according to Motor Authority. After losing their lid, they gained a cloth soft top that opens and closes at the push of a button. There's no word on what effect the conversion has on handling, or what Convertible Builders did to offset the loss of structural rigidity. The build didn't include mechanical modifications. Two of the convertibles are R/T Scat Pack models equipped with a 6.4-liter Hemi V8 engine that serves 485 horsepower and 475 pound-feet of torque. It's not a supercharged Hellcat V8, but it's potent enough to spin the rear wheels in third gear. The third, R/T-based model features a 375-horsepower, 5.7-liter V8. While our dream build would use a six-speed manual transmission, all three come with an eight-speed automatic that sends the engine's power to the rear wheels. Keffer's website lists the gray, white, and red cars at $64,000, $60,000, and $56,300, respectively. The regular R/T Scat Pack Widebody model starts at $46,245, and the eight-speed automatic adds another $1,595, so the convertible conversion adds about $16,000. It's your only option, unless you're brave enough to chop the top yourself, or patient enough to wait until the early 2020s. Dodge has already started developing the next-generation Challenger, so the current car is unlikely to spawn a convertible before it retires. Its replacement due out in 2021 or 2022 will allegedly ride on a wider, longer evolution of the Giorgio platform found under the Alfa Romeo Giulia, among other models, and unverified rumors claim it's being designed with a topless variant in mind from the get-go. It might resurrect the Barracuda nameplate originally assigned to Plymouth when it makes its debut. Auto News Dodge Convertible Performance