2007 Dodge Charger R/t on 2040-cars

Auto blog

Junkyard Gem: 1990 Plymouth Voyager Turbo

There was a time when the word "TURBO" was king, and even Detroit minivans came with nervous, hair-drier-boosted engines and screaming TURBO badging. Why, some of them even had manual transmissions (sadly, not this van) and in the case of the 1990 Plymouth Voyager Turbo I spotted in a Denver self-service wrecking yard, a lysergic purple paint plus a Bordello Red interior. The first-generation Voyager minivan (not to be confused with the full-sized B-series Voyager van that preceded it) was a tremendous smash hit for Chrysler. Because it came from the K-Car platform, most of the powertrain options available for other members of the many-branched K Family Tree— from the Mitsubishi Astron to the Chrysler turbo 2.5— went into the Voyagers, Caravans, and Town & Countries. The turbocharged 2.5-liter four, rated at 150 horsepower, was an option for the 1989 and 1990 Voyagers. That doesn't sound like much today, an era in which the Voyager's descendants churn out close to 300 horses, but it was lunacy for a front-wheel-drive family hauler that weighed just over 3,000 pounds. And people eventually discovered they could be made far faster than stock. Voyager shoppers could get five-speed manual transmissiona with their Turbo 2.5 engines, though few did. Still, there were more Voyagers and Caravans with the 5-speed than you might think, in part because of the manual transmission's lower cost. The slushbox didn't conquer the Chrysler Corporation Minivan World until 1996. Nissan probably had the most vividly red interiors of the late 1980s and early 1990s, but Chrysler didn't lag far behind. Look at these acres of shiny red plastic and tough, red I Can't Believe It's Not Velour! Because minivans remain useful for decades, most of them have high odometer readings by the time they get junked. So at a little over 115,000 miles, this one may have had a busted speedometer cable. Speedometers reading better than 85 mph were legal after 1981, but perhaps Chrysler decided not to encourage lead-footed hoonery among minivan drivers. This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings. Auntie Entity pitching "the best-loved minivan in the world." Featured Gallery Junked 1990 Plymouth Voyager Turbo View 19 Photos Auto News Chrysler Dodge Automotive History Minivan/Van dodge caravan

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Are you the Dodge Dart SRT4?

Dodge has just confirmed that it will be bringing its newest Dart variant, the Dart GT, to Detroit next week, but we're still in the dark about when we'll see a truly hotted-up SRT4 version. But now, by way of the rumormill anyway, we've got at least one proposed, potentially Dodge-based rendering to light our way.
Seen here is what would appear to be a design sketch of the SRT4 Dart. Obviously the image that has surfaced is of rather low-resolution, but there's at least some evidence to support that it may be legitimate. In the original picture, one can just make out the name Tim Doyle in the lower right corner. As it turns out, Tim Doyle's name is also watermarked on the final design image for the 2011 Dodge Durango Citadel Black & Tan, a model that was shown at SEMA in 2010.
Of course, even if this really is the work of Doyle, there's nothing to say that this image isn't one of a great many potential looks for the future SRT4. In fact, the departure of the cross-hair grille from the Dodge's nose seems like it could be a hard sell, though we do, naturally, dig the sleek hood scoop and the bulked up wheel/tire combination.