1975 Dodge Charger on 2040-cars

Auto blog

Chrysler recalls small number of 2013-2014 cars and trucks over engine debris

Chrysler is recalling a small number cars over issues with their 2.4-liter four-cylinder engines. The recall, which affects 522 examples of its 2013 Dodge Avenger and Chrysler 200 models, as well as 2014 Jeep Compass and Patriot CUVs has to do with potential debris in the balance shaft bearings.
The abrasive stuff can cause the oil pressure to drop, which could lead to the engine stalling or outright failure. This situation could at best leave drivers stranded and at worst lead to a crash.
Chrysler will begin notifying owners, who will need to report in to have the balance shaft module replaced. All repairs are naturally free of charge. Scroll down for the bulletin from NHTSA.

Make Your Dodge Durango Even Better | MoPar Options for R/T, SRT | 2018 Chicago Auto Show

Fiat Chrysler is showing new performance add-ons for the 2018 Dodge Durango R/T and SRT models at the Chicago Auto Show, including the familiar Dodge dual center stripes and a new Mopar exhaust system. The 475-horsepower SRT model, which is powered by a 6.4-liter Hemi V8, will also offer a lowering spring kit and a carbon-fiber instrument panel. Chicago Auto Show Dodge Autoblog Minute Videos Original Video SRT

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.