1972 Dodge Charger Rallye 440 on 2040-cars

Auto blog

Junkyard Gem: 1987 Dodge Ram 50 with V8 swap

Chrysler did very well selling Mitsubishi Forte pickups with Plymouth and Dodge badging in the United States, even after Mitsubishi began moving the same trucks out of their own American dealerships in 1982. The 1987 Ram 50 2WD short bed weighed in at just over 2,500 pounds, so it was reasonably perky with its 2.0-liter G63B four-banger making 90 horsepower… but there's no replacement for displacement! At some point along the line, a Chrysler small-block V8 engine found its way into the engine compartment of this truck, now residing in a car graveyard in Sparks, Nevada. This was the cheapest new Dodge-branded pickup Americans could buy as a 1987 model, though it had to compete with its near-identical Mitsubishi Mighty Max twin for sales. The 1980s were great times for little pickups in the United States, but a desire for bigger cabs and more creature comforts doomed them by the dawn of the following decade. The most interesting thing about this engine swap is that it didn't involve a Chevrolet or Ford small-block V8. Both the Chevy small-block and Ford Windsor V8s are a few inches narrower than the Chrysler LA-series V8, which makes them easier to stuff into a small vehicle. It appears that engine length was the critical dimension in this case, since the Mopar seems to have had enough side-to-side clearance to avoid any slicing of Mitsubishi steel to make it fit. My guess is that whoever did the swap happened to have the engine handy and that's why it's here. Keeping it all Dodge might have been a factor in the decision as well, though the truck's Mitsubishi ancestry makes that unlikely. It was over 100°F out when I found this truck, so I wasn't motivated to check block casting numbers to determine exactly which LA engine we're dealing with here. The easiest LAs to get cheap for the last four or so decades have been the 318 (5.1-liter) and the 360 (5.8-liter), so one of those two is the most likely candidate here. Power levels for these engines got pretty dismal during the Malaise Era, but anyone with the wrenching skills to do this swap would have applied some basic power-enhancing wizardry before the engine went in. We can see there's an Edelbrock Performer intake manifold, and you might as well stab in a better camshaft if you're upgrading the intake. How much power? With a four-barrel carburetor on a dual-plane intake plus a meaner cam, 300 to 350 horsepower is easily achieved with one of these engines, even with stock exhaust manifolds.

Will the Dodge Demon do a 10-second quarter-mile?

The final teaser for the Dodge Demon is finally here, and it might just give us a clue as to how quick the new car really is. A brief glimpse at a time slip shows what might be a 10-second quarter-mile time. That's a significant step up from the standard Hellcat's 11.7 seconds, but considering all of the Demon's modifications, it's not an unreasonable time. The new video, "Judgment Day," shows the new Demon in its natural habitat, a quarter-mile drag strip. There isn't much new information, aside from the brief glimpse at a time slip. There is a good shot of the car in action and some nice audio from what we assume is a supercharged 6.2-liter Hemi. For comparison, the new 2016 Chevrolet COPO Camaro is capable of a 10.7-second quarter-mile run, while the 2016 Ford Mustang Cobra Jet dips all the way down into the 8s. The full reveal is less than a week away. Look for more information, including the long-awaited horsepower rating, next week during our coverage of the 2017 New York Auto Show. Related Video: New York Auto Show Dodge Coupe Performance dodge demon dodge hellcat

All hail the Hellephant, Mopar's 1,000-horsepower crate engine

It's shocking to say this, but the all-powerful Dodge Demon looks weak now that Mopar has unleashed the Hellephant. This crate motor makes 1,000 horsepower and 950 pound-feet of torque, and its name is a combination of the nickname for the old 426-cubic-inch Hemi V8 and, obviously, the Hellcat. This monster is a 426-cubic-inch version of the current third-generation Hemi V8 topped by a supercharger similar to what the Hellcat line packs. Everything is cranked up to — or perhaps, past — 11. The engine block is made of aluminum and weighs 100 pounds less than the equivalent iron block. All of the internals are forged. The stroke and bore have been increased. The supercharger produces 15 pounds of boost and displaces 3 liters; more than the 2.7-liter blower on the Demon and the 2.4-liter blower on the Hellcat. And as big and powerful as it is, it will still rev to 7,000 rpm. It's a thoroughly monstrous motor, but shockingly, it won't be that difficult to live with. For one thing, Mopar will offer a complete kit to get the engine up and running, including an engine computer, wiring harness and drive-by-wire throttle. It also runs on 93-octane pump gas. That's especially amazing considering the Demon engine "only" makes 840 horsepower, and that's on race gas with 100+ octane fuel. It also has us wondering what the Hellephant could make on racing fuel. The Mopar folks did say that there's room to add more power. Pricing wasn't announced for the Hellephant engine. The Hellcat crate engine retails at $19,350 directly from Mopar, so it's safe to assume that the Hellephant will go for more. The installation kit with the computer and harness will be an extra charge of likely over $2,000, based on the Hellcat kit. The engine and the kit will be available in the first quarter of 2019. Related Video: Featured Gallery Hellephant Crate Engine SEMA Show Chrysler Dodge Jeep RAM Performance dodge demon hellephant