1971 Dodge Charger Base Coupe 2-door 7.2l on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

NHTSA investigating 110,000 Ram 2500s and 3500s, one death alleged

The National Highway Traffic Safety Administration has launched an investigation focusing on 110,000 Dodge Ram 2500 and 3500 pickups from model years 2004 to 2006. One death has already been reported, according to NHTSA, due to a potential fault with the clutch interlocks on manual-transmission versions of the heavy duty pickup.
According to the report, these trucks can be started without depressing the clutch. There have been three reports so far, and as we mentioned above, one very sad incident seems to have resulted in the death of a child.
"One complaint involved an incident that occurred when a child was able to enter the vehicle and start the ignition without depressing the clutch. The vehicle then moved forward striking another child resulting in a fatality," NHTSA said in the investigation bulletin, which you can view below.

Fiat Chrysler will invest up to $1.5 billion to build EVs in Windsor

Fiat Chrysler Automobiles will invest between $1.35 billion and $1.5 billion in its Windsor assembly plant in Canada to build electric vehicles as part of a tentative deal with Canadian autoworkers, Unifor National President Jerry Dias said on Thursday. The auto union said FCA would invest in a state-of-the-art vehicle platform that will enable the assembly of plug-in hybrid and battery electric vehicles, with at least one new model in 2025. The announcement comes less than a month after Unifor said Ford would invest $1.46 billion in its Oakville and Windsor plants. "Not only is Fiat-Chrysler maintaining the current portfolio but they will be investing three derivatives to enhance the current portfolio," Dias said. Unifor also said it expects to extend the life of the Chrysler 300, a rear-wheel-drive luxury car and introduce multiple derivatives of the Dodge Charger and Challenger. The union said as many as 2,000 jobs would be added in 2024 at the Windsor plant. Market forecasting firm LMC Automotive on Thursday said it would take until 2024 for U.S. vehicle sales to recover from the coronavirus downturn and get close to the 17 million vehicles sold in 2019. Ratification meetings for the FCA deal will happen over the weekend, and members will vote on whether to accept the agreement on Sunday. The union is expected to begin negotiations with General Motors's Canadian unit next week. Related Video: Green Hirings/Firings/Layoffs Plants/Manufacturing UAW/Unions Chrysler Dodge Fiat Jeep RAM Coupe Electric Sedan windsor