Srt-8 Navigation Sunroof Hemi Stripes Brembo Htd Seats 2009 Dodge Challenger 39k on 2040-cars

Auto blog

Dodge idles Viper production again at Conner Avenue

You've got to hand it to Dodge for having the gumption to put the original Viper into production in the first place. It was, after all, much more of an emotional decision than a practical one, and a move which saw the first production V10 engine placed in a road car - long before the advent of the Lamborghini Gallardo, Audi R8, Porsche Carrera GT or Lexus LFA, not to mention the other Ford, BMW and Volkswagen Group models that used such engines.
It's now been 22 years since the first Viper entered production and the Viper still rolls on several generations later, but we're sad to say that courageous decision has not always been met with overwhelming sales success. In fact parent Chrysler was forced to idle the Conner Avenue plant where the Viper is made back in April due to slow sales. And while production resumed again as planned on June 23, it apparently didn't do the trick.
As a result, Chrysler corporate communications chief Shawn Morgan revealed to Autoblog that the assembly line has been shut down again for another two weeks. The line was up and running for nearly two full work weeks from June 23 until the holiday weekend that started on Thursday, July 3. But instead of coming back online today as planned, it's been idled again for the weeks of July 7 and 14. That means it will be July 21, at the earliest, before the serpentine supercars start slithering down the assembly line at Conner Avenue again. Once it does, however, production is set to resume at the same pace it was before the shutdown.

Dodge Journey and Fiat Freemont engine-cover recall affects 350k CUVs

FCA is recalling 349,731 examples of the 2011-2015 Dodge Journey and Fiat Freemont worldwide to better secure their engine covers. Of these affected vehicles, there are 144,416 in the US, 43,679 in Canada, 46,231 in Mexico, and 115,405 elsewhere. About 10 percent of them are also still at dealers, according to the automaker. Only models with the 2.4-liter four-cylinder engine are affected by this campaign. According to the company, the engine covers on these vehicles can be dislodged, and this can pose a fire risk if the loose part comes in contact with hot exhaust components. Warning signs of this happening include a noise under the hood, burning smell or a light on the instrument panel. The problem was discovered after three incidents on rough roads in Chile, and there was one minor injury there. According to FCA US spokesperson Eric Mayne to Autoblog, there have been eight occurrences of this issue reported in the US, but these were all related to "heat damage." There have been no reported injuries here. To fix the problem, dealers will install new engine-cover retainers on the affected models. These repairs will begin in August. As always for recall repairs, owners won't be charged. Statement: Engine Cover July 22, 2015 , Auburn Hills, Mich. - FCA US LLC is voluntarily recalling an estimated 144,416 crossover utility vehicles (CUVs) in the U.S. to better secure their engine covers. Engine covers in certain vehicles may become dislodged. If they come in contact with exhaust components, it may pose a fire risk. This condition was discovered during an FCA US investigation of three incidents in Chile. In each case, the vehicle had been driven extensively on unpaved or uneven surfaces. The Company is aware of a single related injury, described as minor. Affected are 2011-2015 Dodge Journey and Fiat Freemont CUVs equipped with 2.4-liter, four-cylinder engines. FCA US will install upgraded engine-cover retainers in these vehicles. The remedy will be available when customer notification begins next month; service will be performed free of charge. Vehicles equipped with six-cylinder engines are not affected. Additional Journey and Freemont populations also are subject to this campaign. They comprise an estimated 43,679 vehicles in Canada; 46,231 in Mexico; and 115,405 outside the NAFTA region. Of the 349,731 total vehicles subject to this campaign, approximately 10 percent remain in dealer hands.

Will the Chrysler 300 go front-wheel drive?

FCA chief executive Sergio Marchionne hinted last week that the strapping rear-wheel-drive Chrysler 300 sedan could go front-wheel drive for its next generation using the underpinnings from the Chrysler Pacifica minivan. Speaking at the Pacifica's production launch in Windsor, ON, Marchionne said, "this plant and this architecture is capable of making the 300 successor, the front-wheel, all-wheel-drive successor," Reuters reported. Perhaps realizing he appeared to be announcing a dramatic shift in product strategy, Marchionne backpedaled in response to a follow-up question, noting only that the Ontario factory is "capable" of making the sedan. "It's capable. It's not a commitment," he said, according to Reuters. The 300 is currently built in Brampton, ON, alongside the mechanically similar Dodge Charger and Challenger. The platform, known as LX in enthusiast circles, is an evolution of Mercedes-based chassis pieces that date to the DaimlerChrysler era. Marchionne's comments didn't cover the Dodges and left a lot open to interpretation. The 300 could switch to front- and all-wheel-drive and focus on a more civilized, elegant ride character, leaving the Charger and two-door Challenger as traditional rear-wheel-drive muscle cars. That strategy would further differentiate the Chrysler and Dodge car lines. Additionally, the Charger's RWD platform makes it a popular police vehicle, and both Dodges are offered in top trim as 707-horsepower Hellcats. Switching to front-wheel drive would seemingly complicate both of those endeavors. Rumors have also swirled that Alfa Romeo could contribute RWD underpinnings for Dodge. Related Video: Featured Gallery 2015 Chrysler 300 View 92 Photos Design/Style Chrysler Dodge Off-Road Vehicles Performance Sedan chrysler pacifica