2015 Dodge Challenger Srt Hellcat - 6 Speed Manual Transmission on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Chrysler killing off the 200 Convertible, Dodge Avenger

When Chrysler rolled out the first-generation 200 to replace the Sebring range in 2010, it included replacements for both the sedan and the convertible. The Sebring Coupe, however, was left out of the mix. And now that the second-generation Chrysler 200 is descending upon us, Auburn Hills is paring things down even further. But this time, it's the convertible that reportedly isn't making the cut. Shame, too, since the rendering above shows what could have been quite an attractive droptop.
As our compatriots at Edmunds point out, sales of the convertible model accounted for less than five percent of overall Chrysler 200 sales, and at those numbers, the considerable cost of engineering a new drop-top couldn't be justified. With the Toyota Camry Solara and Volkswagen Eos also gone from the market (well, the VW isn't gone quite yet), the discontinuation of the Chrysler 200 Convertible leaves the affordable convertible segment largely to the sportier likes of the Ford Mustang and Chevy Camaro and smaller European offerings like the Mini Cooper and VW Beetle.
The Chrysler 200 Convertible isn't the only derivative being left behind with the new model: so too is the Dodge Avenger. That will leave a glaring hole in the Dodge lineup, with nothing to bridge the gap between the compact Dart and the larger Charger. Whether the Dodge brand has any plans to replace the Avenger with another model, not to be based on the 200, remains to be seen.

NHTSA investigating power modules on Chrysler Group SUVs and minivans

The Center for Auto Safety is officially petitioning the National Highway Traffic Safety Administration to begin scrutinizing alleged problems with the totally integrated power module (TIPM) on about 24 Chrysler Group SUVs and minivans. The advocacy group claims that the part's failure can cause affected vehicles to stall or not start at all. NHTSA is still looking into the accusations and deciding whether a full investigation is actually warranted.
The CAS petition claims at least 70 TIPM failures, but according to NHTSA, six of the complaints are for models that don't have the modules. In 34 of the reported cases, the vehicles refused to start, and in 17 of them the engine stalled. There were also two allegations of smoke and one of a fire. However, none of these affected airbag deployment or resulted in a crash.
This petition isn't the first TIPM-related problem for Chrysler Group. A recent report in the New York Times alleged that it found 240 complaints potentially related to the issue on NHTSA's website alone. In September, the automaker also recalled 230,760 examples worldwide (188,723 in the US) of the 2011 Jeep Grand Cherokee and Dodge Durango replace the fuel pump relay circuit inside of the TIPM-7 with one external to the unit. The original part could allegedly cause the models to stall without warning. Even earlier, the company also recalled about 80,000 examples of the Jeep Wrangler and Dodge Nitro in 2007 to have the module reprogrammed.