2013 Dodge Challenger R/t on 2040-cars

Auto blog

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

McLaren, Koenigsegg, Toyota, Ford, Dodge and Corvette Lego kits announced for 2021

Lego has announced a slew of car-themed sets for 2021. The six kits comprise nine vehicles and fall under the brick pusher's Speed Champion line of official OEM-licensed kits. News of their arrival comes from German toy retailer JB Spielwaren's pre-order listings, which show three single-car sets and three dual-car sets of matched marques. Starting with the McLaren Elva roadster, the kit consists of 263 pieces and is finished in blue. It seems to have a difficult time capturing the curves of the real-life Elva, but there's only so much you can do with a bunch of plastic blocks. Lego has made several other McLaren kits before, including the Senna, 720S, and a more advanced Senna GTR for the Technics line. Next up is the Koenigsegg Jesko, made up of 280 pieces and finished in white. Though the real-life Jesko is still curvy, this kit does a better job of replicating its aggressive maw, vents and cantilevered rear wing. Rounding out the single-car sets is the 299-piece Toyota GR Supra in yellow. This marks the first time Toyota has lent their license to Lego. Again, it struggles a bit to represent the curvy Supra, relying on printed details like logos and headlights to identify. On the other hand, the Chevrolet two-car does a stupendous job with the 1968 Corvette. The C3 is instantly recognizable as such. The C8-R race car it's paired with suffers from the same issues as some of the previous cars, though. The set contains 512 pieces, and funnily enough the C8 driver has short hair while the C3 driver sports a period-correct wavy mane. The next set is a 627-piece Mopar-themed pair, including a purple (Plum Crazy?) 1970 Dodge Challenger T/A and an SRT top fuel dragster. The race car is spot on, but the Challenger was probably tough to make given the width restrictions. It looks a couple of pegs too narrow compared to the wide proportions of the real deal. Last but not least, the Ford set contains a Bronco R and Ford GT Heritage Edition. Consisting of 660 pieces, the set does an excellent job of representing both cars. The GT looks faithful in its Gulf livery, and the Bronco R looks more like a real Bronco than the actual Bronco R race truck. All in all, it's always fun to see more Lego sets with real cars, and we're glad to see more manufacturers added to the roster. The single-car sets are recommended for ages 7 and up, while the double-car sets have an 8 years and up rating. Price in U.S.

Chrysler recalling 278,222 trucks and SUVs over bad rear axles

Chrysler has issued a recall of 278,222 light trucks and sport utility vehicles here in the United States. The reason: bad rear axles. Specifically, according to the National Highway Traffic Safety Administration, the rear axle pinion nut may lack a necessary adhesive patch, which could cause the nut to loosen. If this happens, the axle can lock up, which could cause all sorts of havoc on the road.
This is an expansion of the rear axle recall announced in October of last year, where 44,300 Ram 1500 and Dodge Dakota models were being called in. At that time, 12 accidents had been reported due to the faulty axle pinion nut.
Affected vehicles include Ram 1500 trucks from the 2009 to 2012 model years, Dodge Dakota models from the 2009 to 2011 model years, and both the Chrysler Aspen and Dodge Durango SUV twins, both from the 2009 model year only.