2013 Dodge Grand Caravan Sxt Stow N Go 7-passenger 32k Texas Direct Auto on 2040-cars

Auto blog

Will the Chrysler 300 go front-wheel drive?

FCA chief executive Sergio Marchionne hinted last week that the strapping rear-wheel-drive Chrysler 300 sedan could go front-wheel drive for its next generation using the underpinnings from the Chrysler Pacifica minivan. Speaking at the Pacifica's production launch in Windsor, ON, Marchionne said, "this plant and this architecture is capable of making the 300 successor, the front-wheel, all-wheel-drive successor," Reuters reported. Perhaps realizing he appeared to be announcing a dramatic shift in product strategy, Marchionne backpedaled in response to a follow-up question, noting only that the Ontario factory is "capable" of making the sedan. "It's capable. It's not a commitment," he said, according to Reuters. The 300 is currently built in Brampton, ON, alongside the mechanically similar Dodge Charger and Challenger. The platform, known as LX in enthusiast circles, is an evolution of Mercedes-based chassis pieces that date to the DaimlerChrysler era. Marchionne's comments didn't cover the Dodges and left a lot open to interpretation. The 300 could switch to front- and all-wheel-drive and focus on a more civilized, elegant ride character, leaving the Charger and two-door Challenger as traditional rear-wheel-drive muscle cars. That strategy would further differentiate the Chrysler and Dodge car lines. Additionally, the Charger's RWD platform makes it a popular police vehicle, and both Dodges are offered in top trim as 707-horsepower Hellcats. Switching to front-wheel drive would seemingly complicate both of those endeavors. Rumors have also swirled that Alfa Romeo could contribute RWD underpinnings for Dodge. Related Video: Featured Gallery 2015 Chrysler 300 View 92 Photos Design/Style Chrysler Dodge Off-Road Vehicles Performance Sedan chrysler pacifica

Stormtrooper Dodge Charger Episode VII: The Charger Awakens

We spent a day with a Dodge Charger that looks like a Stormtrooper helmet and made a few videos. This one features the Hemi V8 starting up. Read about the car and watch the rest of the videos here.

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat