Chrysler Town And Country 7 Passenger Van on 2040-cars

Auto blog

More Ram trucks recalled over tailgate issue

Almost a year ago Fiat Chrysler recalled roughly 1.6 million Ram trucks over an issue with the locking power tailgate. The actuator limiter tab for the power locking mechanism could fracture, which would permit the actuator's lock-rod control to move beyond its limits. That would pull the locking rods open, thereby allowing the tailgate to open at any time. The 2018 recall covered Ram 1500, 2500, and 3500 pickups from the 2015 to 2017 model years, with the five-foot-seven and six-foot-four beds and the power locking tailgate option. Trucks with eight-foot beds, and those with manual-locking tailgates, were excluded. The trucks with eight-foot beds have been added to the recall as of earlier this month, putting 410,351 more trucks in the pool. According to Consumer Reports, Ram redesigned the locking assembly on the other two shorter bed sizes for trucks built after August 2, 2017, which was the end of the 2017 model year. But the eight-foot long-bed trucks didn't get the redesigned part until April 2, 2018 for some reason, making all eight-foot-bed pickups from the 2015 model year to April 1, 2018 part of the recall equation. FCA says it's not aware of any accidents or injuries because of the issue. The company plans to notify owners on June 28. The paperwork filed with the National Highway Traffic Safety Administration doesn't advise owners to stop driving the trucks, but nor does it instruct owners on how to address the problem in the meantime. Sounds like bungee cords might be the go. The fix is estimated to take 30 minutes at the dealer and entails removing the tailgate cover and installing a stop block to prevent the locking actuator's pivot arm from traveling too far. FCA says it will reimburse owners for any other repairs made to address the problem. Meanwhile, owners can contact Fiat Chrysler Automobiles customer service at 800-853-1403, and refer to FCA's number for this recall, V44. The NHTSA campaign number is 19V-347. Last year's recall comes under FCA number U74, and NHTSA campaign number 18V-486. Ram's not alone on this field. The NHTSA continues to investigate the 2017 Ford Super Duty pickups for a similar issue.

Chrysler banks $507 million in Q2, trims 2013 earnings forecast

Chrysler has some good news and some bad news. First, profits were up 16 percent over the second quarter of 2012, bringing the Auburn Hills, Michigan-based manufacturer $507 million on the back of strong demand for trucks and SUVs (a recurring theme this quarter, particularly in the US). Q2 revenue was up as well, from $16.8 billion in 2012 to $18 billion in 2013. The bad news is that the Pentastar's overall earnings forecast for net income in 2013 has been trimmed from $2.2 billion to between $1.7 and $2.2 billion, according to Automotive News.
In addition to the adjusted net income forecast, Chrysler tweaked its operating profit from $3.8 billion to between $3.3 and $3.8 billion. This has gone largely unexplained by Chrysler, perhaps hoping the news of a three-percent increase in its transaction prices for Q2 will allow it to sweep this adjustment under the rug.
The star of the show for Chrysler has been its US sales, which saw a 10-percent jump, both bettering the industry average of eight percent and improving over the same stretch of 2012. As with the increase in transaction prices, Chrysler has the new Ram pickup and Jeep Grand Cherokee to thank. Perhaps most worrying from this report, though, is that every brand in the automaker's stable saw an increase in sales... except for the Chrysler brand itself.

Pentastar Power: A look inside the Detroit factory that pumps out FCA's potent V6

The Mack Avenue Engine Plant is one of Fiat Chrysler Automobiles' most historic and prolific factories. It pumped out 260,000 Pentastar V6 engines last year, providing power for everything from the Jeep Grand Cherokee to the Dodge Challenger. FCA and its predecessor, Chrysler, has owned the factory since 1953 and it briefly built the Dodge Viper in the 1990s. It's made engines since 1998 and began building the Pentastar in 2014. We got an inside look at the mighty Mack, helping to tear down a Pentastar engine and then a tour of the factory floor. This is what it's like. Plants/Manufacturing Chrysler Fiat Videos Original Video pentastar v6