2006 Chrysler Sebring Touring Convertible on 2040-cars

Auto blog

Chrysler recalling 49K Chargers for headlight components

Chrysler has issued a recall for about 49,375 2011 and 2012 Dodge Chargers with halogen headlamps due to a problem with the lights. The automaker says that there could be an issue with the jumper harness and other related components.
The automaker says that 43,450 cars are affected in the US, 2,850 in Canada, 375 in Mexico and 2,700 outside of North America. The vehicles will have their headlight assemblies, including the jumper harnesses and bulbs, inspected and potentially replaced. Dodge says that its engineers investigated reports of that were similar to what was found when it recalled about 10,000 police Chargers in 2012 for overheating light components. There have been no injuries or accidents related to fault, according to Chrysler.
The automaker will be in contact with affected owners, and schedule the service. Naturally, any repairs will be free of charge. Scroll down for the company's full announcement.

Chrysler may be testing a Hellcat 300

Another day goes by, and another mysterious, undisguised SRT prototype comes out of FCA. This time we have a Chrysler 300 SRT that looks nearly stock except for its footwear. Our spy photographer got up close and personal with this machine, and found that it has the same wheels with 315-mm tires that were on the early Dodge Demon prototypes. The only difference is the wheels on this 300 have Chrysler-branded center caps. All that extra width means these wheels stick pretty far out from the wheel wells, which would suggest that any production car running this setup would have flares to cover the wheels. Behind those wheels are four-piston Brembo calipers and slotted discs that looks similar to those on the current 300 SRT. We doubt that Chrysler is building a Demonized version of the 300, but the tires do suggest that this is a much more potent 300 than the current SRT, which was discontinued in the US in 2015 but is still sold in the Middle East and Australia. That's not all we have to go on, though, since our spy photographer says it sounded like it had Hellcat power under the hood. Equipping a 300 with a Hellcat engine would be a breeze, too, since the engine is already in the Charger, which is virtually identical mechanically. What you may be wondering is why Chrysler is adding a Hellcat version of the 300 SRT when that model hasn't been available in the US since 2015. One possible reason is that this would finally allow Aussies access to the 707-horsepower machine. Dodge is not a brand offered Down Under, so it doesn't get the Charger Hellcat, leaving the 300 as the only V8, rear-drive Mopar available. And for the Middle East, if the normal 300 SRT was selling well, it would only make sense to offer another variant. It shouldn't cost Chrysler too much to develop this model either, since the 300, mechanically, is virtually identical to the Charger. Related Video: Featured Gallery Chrysler 300 SRT Hellcat Widebody Spy Photos View 16 Photos Image Credit: Brian Williams Spy Photos Chrysler Performance Sedan chrysler 300 srt8

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.