2014 300c New 3.6l V6 24v Automatic Rwd Sedan on 2040-cars

Auto blog

NHTSA investigating power modules on Chrysler Group SUVs and minivans

The Center for Auto Safety is officially petitioning the National Highway Traffic Safety Administration to begin scrutinizing alleged problems with the totally integrated power module (TIPM) on about 24 Chrysler Group SUVs and minivans. The advocacy group claims that the part's failure can cause affected vehicles to stall or not start at all. NHTSA is still looking into the accusations and deciding whether a full investigation is actually warranted.
The CAS petition claims at least 70 TIPM failures, but according to NHTSA, six of the complaints are for models that don't have the modules. In 34 of the reported cases, the vehicles refused to start, and in 17 of them the engine stalled. There were also two allegations of smoke and one of a fire. However, none of these affected airbag deployment or resulted in a crash.
This petition isn't the first TIPM-related problem for Chrysler Group. A recent report in the New York Times alleged that it found 240 complaints potentially related to the issue on NHTSA's website alone. In September, the automaker also recalled 230,760 examples worldwide (188,723 in the US) of the 2011 Jeep Grand Cherokee and Dodge Durango replace the fuel pump relay circuit inside of the TIPM-7 with one external to the unit. The original part could allegedly cause the models to stall without warning. Even earlier, the company also recalled about 80,000 examples of the Jeep Wrangler and Dodge Nitro in 2007 to have the module reprogrammed.

Michigan Gov. Gretchen Whitmer says manufacturing can reopen May 11

Michigan Governor Gretchen Whitmer on Thursday said the state's factories can reopen next Monday, May 11, removing one of the last major obstacles to North American automakers bringing thousands of laid-off employees back to work amid the coronavirus pandemic. While reopening the manufacturing sector, Whitmer also extended her state's stay-at-home order by about two weeks to May 28, citing a desire to avoid a second wave of COVID-19, the respiratory illness caused by the novel coronavirus. “WeÂ’re not out of the woods yet, but this is an important step forward," Whitmer said in a statement. "As we continue to phase in sectors of our economy, I will keep working around the clock to ensure our businesses adopt best practices to protect workers." This week, General Motors and Fiat Chrysler Automobiles said they were targeting resuming vehicle production in North America on May 18, but suppliers would need time to prepare ahead for that date. Ford has not said what date it is targeting. The governor previously extended the state's coronavirus stay-at-home order through May 15, but had lifted restrictions for some businesses. Neighboring Ohio had allowed manufacturing to resume this past Monday, putting pressure on Whitmer to follow suit. Michigan's shutdown had stymied efforts by the Detroit Three and rival automakers to restart vehicle assembly anywhere in the United States, because so many critical parts suppliers are based in the state. Automakers and their suppliers already have begun gearing up for a possible resumption of work at their U.S. plants, but needed the official go-ahead from Whitmer. Industry officials had been pressing Whitmer to allow suppliers to reopen starting May 11 so the automakers could resume operations on their target date. They also wanted the green light so they can press Mexico to open its auto sector as suppliers there are also critical for the industry restart. The automakers' plans were tacitly approved on Tuesday by the United Auto Workers union, which represents the Detroit automakers' hourly U.S. plant workers. The union had previously said early May was "too soon and too risky" to restart manufacturing. Under Whitmer's new order, factories must adopt measures to protect workers, including daily entry screening, no-touch temperature screening as soon as possible and use of protective gear like face masks. Automakers have already rolled out such policies.

Plymouth Belmont: Running, driving, Virgil Exner-owned concept car could be yours

Concept cars are such bittersweet things. They're often gorgeous and exciting, but all too often they never see production in even the most watered-down forms. And even then, the beautiful shapes aren't usually driveable. But in the case of this 1954 Plymouth Belmont concept, it is drivable, and it could be yours. This curvaceous roadster, which appeared at the 1954 New York Auto Show and was owned at one time by Chrysler styling master Virgil Exner, is driveable because under the long hood is a 241-cubic-inch V8 coupled to a three-speed automatic transmission. It's not a speed demon with just 157 horsepower, but that's OK, because you don't want to accelerate so fast you deprive the world of the Belmont's beautiful body. For a design from the 1950s, it's impressively restrained and elegant. The flanks are completely smooth and flowing, the only interruptions being the shut lines to the small doors. There aren't even door handles on the sides. Chrome and polished stainless accents are left only to the lights, bumpers, grille, and a slender line that runs along the peak of the fenders from stem to stern. Even the fins are small and subtle (relatively). Even the interior is simple and clean. The dashboard is made of machine-turned metal with white on black analog dials and compass-like needles. Everything else is wrapped in a very light beige leather (probably vinyl), and again, polished surfaces are kept to a minimum. Of course the other great part is that this concept is something you could own because it will go for auction at Barrett-Jackson's Scottsdale auction. There's no publicly available estimate for how much money the car may bring, but it does have a reserve, so be prepared with a little extra cash even if you have the winning bid. The auction runs from Jan. 13 to Jan. 21. Related Video: Image Credit: Barrett-Jackson Chrysler Auctions Convertible Concept Cars Classics