2011 Chrysler 300c 300c on 2040-cars

Auto blog

NHTSA looking into non-Takata airbag shrapnel case

The global airbag inflator recall from Takata has been one of the biggest topics in auto safety for months. Now, the National Highway Traffic Safety Administration is opening a preliminary evaluation into the components from Arc Automotive to investigate whether two reported ruptures and two injuries signal a wider problem. So far, only the 2002 Chrysler Town & Country and 2004 Kia Optima are believed to be affected. If a safety campaign is deemed necessary, it could cover an estimated 420,000 of the minivans and 70,000 of the Korean sedans. NHTSA first noticed these ruptures in December 2014. The agency received a complaint of a 2009 case in Ohio about the bursting of the driver's side inflator in a 2002 Town & Country. According to the report, the incident broke the woman's jaw and sent shrapnel into her chest. The government investigated the case, and this was found to be the only known occurrence in these vehicles. The analysis indicated the part's gases were possibly blocked somehow and caused the component to explode. FCA US spokesperson Eric Mayne told Autoblog that the company is "cooperating fully" with NHTSA. "Also, we no longer use that inflator," he said. A second incident came to NHTSA's attention in June 2015 with the driver's side rupture in a 2004 Optima in New Mexico. The agency lists fewer details about the case, and a root cause isn't known. This is also the only currently known example in a Kia vehicle. According to a statement from Kia to Autoblog, "We are taking this matter very seriously and support NHTSA's action and will continue working cooperatively with the agency and suppliers throughout the process." Arc's components are sealed within a steel housing that's meant to protect them from "external atmospheric conditions," according to NHTSA. Multiple suppliers also use them. In the Chrysler, the airbag module came from Key Safety Systems and from Delphi in the Kia. In a statement to Autoblog the company said, "We have received NHTSA's notification and are cooperating fully with its Preliminary Evaluation." At this time, NHTSA admits that it doesn't know for certain whether these two cases are linked. The agency is conducting this preliminary evaluation to learn more.

FCA's Pentastar V6 gets more power, efficiency for 2016

Already a vital member of FCA's powertrain lineup, the 3.6-liter Pentastar V6 is receiving major efficiency improvements for 2016. Thanks to a massive amount of new tech attached to the mill, fuel economy is up six percent, and torque below 3,000 rpm jumps nearly 15 percent. The updates arrive first in the 2016 Jeep Grand Cherokee, but they should proliferate to other models eventually. At least in the Grand Cherokee, the tweaks push power up five horsepower to 295 ponies. FCA's engineers went through the Pentastar from top to bottom to eke out as much efficiency as possible. For example, there's now a two-speed variable-valve lift system that can run in low- or high-lift modes. This upgrade is responsible for 2.7-percent better economy, the company claims. A new intake manifold with longer runners and updated variable-valve times also helps boost the torque output. Further improvements come from pushing the compression ratio to 11.3:1, from 10.2:1 before. Perhaps most impressive is that despite all of the innovations, the latest Pentastar actually weighs four pounds less than the current version. Beyond the Pentastar improvements, all of the FCA US gasoline engines, except for the Viper's 8.4-liter V10, will be E15-compatible for 2016. The company says that it wants to be ready for the higher ethanol content fuel's greater use in the near future.

Jeep will build old Wranglers next to new ones in Toledo

Jeep made a lot of people happy when it confirmed that the next-generation Wrangler would continue to be built in Toledo, OH. Now, news is breaking about the lengths the automaker will go to in updating its northern Ohio factory. There's good news for Jeep dealers (more Wranglers to sell!), Jeep fans (more JKs to buy!), and Jeep itself (more money to be made!). According to a report from Automotive News, capacity at the factory will be increased to 350,000 units per year. That's around a 50 percent increase over what the Toledo complex can currently manage and is, according to Jeep boss Mike Manley, part of a move to keep production "at the right place" so "supply [stays] just behind demand." The other big news revealed by the AN report focuses on the future of the current Wrangler. Yes, the current JK has a future. It'll continue to be built at the Toledo factory up to six months after it successor arrives in showrooms, a move that's partially down to the way Jeep is shuffling production about. Toledo currently builds the Cherokee on a unibody production line – it'll continue to do so until March of 2017, when production will move to Belvidere, IL. The unibody line in Toledo will then be converted for body-on-frame production, which should take about six months. But during that time, the current JK (likely rebadged as a "Wrangler Classic") will continue to be built alongside another line of next-generation Wranglers, keeping dealers supplied with the today's Wrangler through March of 2018. The two Wranglers will overlap for about six months. This is all very good news if you've been waiting to pull the trigger on today's Wrangler. But move quickly – the clock is officially ticking. Related Video: News Source: Automotive News - sub. req.Image Credit: Bill Pugliano/Getty Images Plants/Manufacturing Chrysler Fiat Jeep FCA toledo Mike Manley