2014 Chevy Traverse Ls 8-pass 3rd Row Rear Cam 8k Miles Texas Direct Auto on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Want a V8 on the cheap? Buy a work truck

In case you didn't notice, V8 cars have gotten pretty expensive. If you want a modern muscle car like the Dodge Challenger R/T, Ford Mustang GT, or Chevy Camaro SS, you'll need between $34,000 and $38,000 for a stripped out example of one. The cheapest of those is the Challenger, and the priciest is the Camaro. These are also the cheapest V8 cars the companies offer. But if you absolutely have to have a V8 for less, there is an option, work trucks. As it turns out, all of the Big Three offer their most basic work trucks with V8s. And because they're so basic, they're pretty affordable, especially when sticking with the standard two-wheel drive. A Ram 1500 Tradesman with a V8 can be had for as little as $29,840, which is a little more than $4,000 less than a Challenger R/T. For a bit more at $30,275, you can have a Chevy Silverado W/T, almost $8,000 less than a Camaro SS. The most expensive is the V8 Ford F-150 starts at a starting price of $30,670, which is a bit over $5,000 less than the Mustang. Of course you'll be in an ultra bare bones vehicle with few comforts, and the price will go up if you add stuff, but we're bargain hunting here, and sacrifices are sometimes necessary. Besides, what you lose in comfort, you gain in loads of cargo space and towing (try to look at the bright side). Also, as a side note, all three trucks are available with optional electronic locking rear differentials. At the discounted price of these trucks, you still get a heaping helping of power. The most potent of the trio is the Ram 1500 Tradesman with 395 horsepower and 410 pound-feet of torque generated by a 5.7-liter V8. Compared with the Challenger R/T, the Ram is up by 20 horsepower and they're tied for torque. The value proposition is even more stark between the two vehicles when looking at the price per horsepower. Each pony in the Ram costs $75.54, while the Challenger charges you $90.91. The Challenger is also more expensive per horsepower than its close competitors. The F-150's 5.0-liter V8 is just barely behind the Ram with 395 horsepower and 400 pound-feet of torque. That's still more power than the Challenger, and it matches the torque of the 2017 Mustang GT. On the down side, it still would be down 20 horsepower on that same 2017 Mustang, and it's behind by 60 horsepower and 20 pound-feet on the new 2018 Mustang GT. The F-150 also just edges out the Mustang in the dollar per horsepower measure.

Danica Patrick hands over keys to first 2016 Chevy Camaro

Alican "Turk" Boyacioglu got more than he expected this weekend when he picked up his new 2016 Chevy Camaro, the very first sixth-gen Camaro to be delivered to a private customer. That's because racer Danica Patrick was on hand for the delivery. The handing over of the keys took place at Texas Motor Speedway – a stop along the brand's Find New Roads trip. The journey is being conducted to introduce America to five new Chevy models: the Camaro and also the new Malibu, Cruze, Volt, and Spark. The road trip kicked off on October 19 and will conclude next week on November 14. Boyacioglu ordered up a red Camaro SS from Huffines Chevrolet in Lewisville, TX, north of Dallas. When he headed from Kansas to northern Texas to take delivery, he was pleasantly surprised to see Danica climb out of the car to hand him the keys. Though she may have raced under Honda power during her IndyCar days, Danica's NASCAR stock cars have always been powered by Chevrolet. She even drove a Camaro in the Nationwide Series. The smile on Turk's face ought to last him the nearly five-hour drive home to Wichita. For everyone else, deliveries are set to commence in earnest in the middle of this month. The first models to be delivered will be V6 coupes. Convertibles and turbo-four models will start shipping early in the new year. Customers will be able to choose between six powertrain combinations, made up of the 2.0-liter turbo four, the 3.6-liter V6, and the 6.2-liter V8, each available with a six-speed manual or eight-speed automatic. Pricing starts at $26,695 for the base 1LT trim and extends up to $37,295 for the 1SS. DANICA PATRICK SURPRISES CUSTOMER WITH 2016 CAMARO Huffines Chevrolet delivers first 2016 Camaro to Alican 'Turk' Boyacioglu DALLAS – Racecar driver Danica Patrick helped the team at Huffines Chevrolet deliver the first sixth-generation Camaro to a customer from Wichita, Kan., at the Texas Motor Speedway stop of Chevrolet's Find New Roads Trip today. Alican "Turk" Boyacioglu had been eagerly tracking the build of his 2016 Camaro SS and could not contain his excitement when Patrick emerged from the car and handed him the keys. "This whole experience was surreal," Boyacioglu said.