2011 Chevrolet Traverse 1lt on 2040-cars

Auto blog

GM won't really kill off the Chevy Volt and Cadillac CT6, will it?

General Motors is apparently considering killing off six slow-selling models by 2020, according to Reuters. But is that really likely? The news is mentioned in a story where UAW president Dennis Williams notes that slumping US car sales could threaten jobs at low-volume factories. Still, we're skeptical that GM is really serious about killing those cars. Reuters specifically calls out the Buick LaCrosse, Cadillac CT6, Cadillac XTS, Chevrolet Impala, Chevrolet Sonic, and the Chevrolet Volt. Most of these have been redesigned or refreshed within the past few model years. Four - the LaCrosse, Impala, CT6, and Volt - are built in the Hamtramck factory in Detroit. That plant has made only 35,000 cars this year - down 32 percent from 2016. A typical GM plant builds 200,000-300,000 vehicles a year. Of all the cars Williams listed, killing the XTS, Impala, and Sonic make the most sense. They're older and don't sell particularly well. On the other hand, axing the other three seems like an odd move. It would leave Buick and Cadillac without flagship sedans, at least until the rumored Cadillac CT8 arrives. The CT6 was a big investment for GM and backing out after just a few years would be a huge loss. It also uses GM's latest and best materials and technology, making us even more skeptical. The Volt is a hugely important car for Chevrolet, and supplementing it with a crossover makes more sense than replacing it with one. Offering one model with a range of powertrain variants like the Hyundai Ioniq and Toyota Prius might be another route GM could take. All six of these vehicles are sedans, Yes, crossover sales are booming, but there's still a huge market for cars. Backing away from these would be essentially giving up sales to competitors from around the globe. The UAW might simply be publicly pushing GM to move crossover production to Hamtramck to avoid closing the plant and laying off workers. Sales of passenger cars are down across both GM and the industry. Consolidating production in other plants and closing Hamtramck rather than having a single facility focus on sedans might make more sense from a business perspective. GM is also trying to reduce its unsold inventory, meaning current production may be slowed or halted while current cars move into customer hands. There's a lot of politics that goes into building a car. GM wants to do what makes the most sense from a business perspective, while the UAW doesn't workers to lose their jobs when a factory closes.

2016 Camaro gets most revealing tease yet

Chevrolet started its long teaser campaign for the 2016 Camaro by just revealing the exhaust manifold and front frame, but as time has passed the company has slowly unveiled more. In the latest glimpse ahead of the pony car's May 16 debut, we're actually getting to see the model's profile completely undisguised. As suggested by the recent tease of the rear and hood, the 2016 Camaro wears a sharper, more angular design than the current model. This is especially the case when you look at the taut lines making up the rear. Chevy claims that the new shape underwent 350 hours of wind tunnel tests to be able to generate left lift, improve cooling and reduce wind noise in the cabin. A smooth underbody pan is among the aerodynamic tweaks, and it runs from underneath the front grille to the center of the Camaro. Chevy asserts that all of the changes at the front help reduce lift by 30 percent. Related VIdeo: 2016 Camaro is all about the Aero Total aerodynamic lift improved by 30 percent for improved stability 2015-05-11 DETROIT – After 350 hours of wind tunnel testing – often 24 hours a day – the new Camaro will slip more easily through the wind, and drivers of the Camaro SS will experience a marked improvement in reduced aerodynamic lift. These changes illustrate the lengths the aerodynamics team went to for improved performance, stability, cooling and lower wind noise intrusion "The importance of aerodynamics increases exponentially as we increase vehicle performance," said Kirk Bennion, Exterior Design manager. "As engine output increases, we need more engine cooling. As acceleration and top speeds climb, we need to reduce lift for better high-speed stability. However, we cannot make any changes at the expense of increasing drag, which can hurt fuel economy. "To balance these different aerodynamic targets, we tested literally hundreds of changes on the new Camaro, millimeters at a time." For example, the initial design called for the lower grille bars to be set at a 20-degree angle to the horizon. However, after meticulous testing, the team improved engine-cooling airflow by 1 percent by shifting the angle to 13 degrees – a change that achieved the airflow target while maintaining the original grille design. And rather than a traditional front air dam to reduce aerodynamic lift, the team developed a flush belly pan that stretches from the front grille to the center of the vehicle.

GM might outsource vans to AM General

General Motors will possibly boost production of the Chevrolet Colorado and GMC Canyon at the Wentzville Assembly Plant in Missouri by contracting out some commercial van manufacturing to AM General. Demand for the two midsize trucks continues to boom, and GM would like to take advantage of the strong market for them. The possible deal came to light in a letter to workers at the factory, according to Automotive News. "This potential partnership would free up production capacity and allow the organization to capitalize on our ability to build midsize trucks to further satisfy customer demand," a portion of the document allegedly said. AM General would reportedly only take over assembly of the cutaway versions of the Chevy Express and GMC Savana. Customers and critics have quickly embraced the latest Colorado and Canyon since their introduction. The Chevy just won back-to-back Motor Trend Truck of the Year awards. GM also had to add a third shift and extra workers in 2014 just to keep up with demand. The Wentzville plant even increased employment on the weekends earlier in 2015 to assemble an extra 2,000 of the trucks each month. While the two pickups boom, deliveries for the Chevy Express and GMC Savana are down 26.9 percent and 26.6 percent respectively through the first 10 months of the year. GM doesn't break out numbers for the cutaway versions, but they make up about a third of production, according to Automotive News. AM General built the Humvee for the US military and does some contract work with automakers. For example, the company's Indiana factory now produces the Mercedes-Benz R-Class for export to China. Here's hoping this potential deal will help both GM and AM General keep their factories humming. Related Video: