2007 Chevrolet Tahoe Ltz 4x4 Luxury Sport Utility 4wd Smart Chevy Suv 3rd Row V8 on 2040-cars

Auto blog

GM patent reveals new two-stage turbocharger

Modern turbochargers may be some of the best ever made, but performance is something that engineers are always trying to improve. According to GM Inside News, General Motors (GM) is hoping to alleviate some of the negative aspects of a two-stage turbocharger setup with a newly-patented design. The patent, that was filed on May 19, 2016, reveals a clever bypass system that allows the engine, a four-cylinder unit, to optimize both the low-pressure and high-pressure inlets for its respective functions. According to the filing, a conventional two-stage turbocharger setup is engineered to allow both turbines to operate simultaneously at low and mid engine speeds. At high engine speeds, only the low-pressure turbine works. The setup can't isolate either the low or high pressure side, which can impair low-end performance. GM's new two-stage turbocharger setup looks to eliminate this by linking the high-pressure turbo to the exhaust manifold through the high-pressure inlet duct. The low-pressure turbo is attached to the high-pressure turbo by a low-pressure inlet duct, which is linked to a connecting channel. A single actuator that is housed in the exhaust manifold creates a bypass that can opens the high-pressure inlet or close the connecting channel. Depending on what the engine load and speed is, the ECU guides the actuator—a single rotating spindle with discs corresponding to flanges on the high and low pressure sides—to isolate one of the two turbos. Isolating the turbos allow the respective inlets to be engineered for the best possible fluid dynamic performance. The setup should increase performance and decrease lag. There's no word on what car this setup will make an appearance on, but it will most likely be used in premium vehicles before trickling down to the rest of GM's vehicles. Related Video: News Source: GM Inside News, AutoGuide via GM Authority Cadillac Chevrolet GM Technology Sedan turbo patent engine turbocharging

North American Car, Truck and SUV of the Year finalists revealed

The finalists for the 2023 North American Car, Truck and Utility Vehicle of the Year Awards were announced Thursday at the L.A. Auto Show. — The Acura Integra, Genesis Electrified G80 and Nissan Z made the cut in the car category. — The Ford F-150 Lightning, Chevy Silverado ZR2 and Lordstown Endurance advanced in trucks. — And the Cadillac Lyriq, Genesis GV60 and Kia EV6 advanced among utilities.  The winners will be announced Jan. 11 in Detroit.  The finalists underscored the industryÂ’s shift to electric vehicles, as all three utilities and two of the three trucks are EVs. The finalists were culled from a list of 26 semifinalists made up of three trucks, 10 cars and 16 utility vehicles that are new this year.  Notables that missed the cut include the Mercedes EQE, Subaru WRX and Toyota GR Corolla in cars; while the Honda CR-V, Kia Sportage and Rivian R1S were among the utes that did not advance. The three trucks are the only ones eligible this year and have advanced through the voting.  50 jurors who work for media outlets across North America vote three times over the course of the year to whittle down the field, which was originally 47 vehicles. Jurors also test the semifinalists at an October group event in Ann Arbor, Mich. The Honda Civic (car), Ford Maverick (truck) and Ford Bronco (utility vehicle) were the 2022 winners. Autoblog Editor-in-Chief Greg Migliore is a NACTOY juror.   Featured Gallery Ford F-150 Lightning View 48 Photos Green LA Auto Show Acura Cadillac Chevrolet Ford Genesis Kia Nissan Truck SUV NACTOY Lordstown Endurance

Why an independent rear suspension for GM's new, full-sized SUVs wasn't easy

A Motor Trend report last month laid out how Cadillac's 4.2-lier twin-turbo Blackwing V8 could be an orphan due to cost concerns in the GM empire. Last-minute chassis changes to Cadillac's new sedans and XT6 crossover led to engine bays that couldn't fit the Blackwing. On the SUV side, according to the report, the new independent rear suspension for big people haulers cost so much to implement that GM ruled out reworking the Escalade to accept the Blackwing. At least one commenter rightly asked how could a suspension swallow that much money. A new piece in Motor Trend has the answer. The excellent Alissa Priddle spoke to Tim Herrick, GM's executive chief engineer for full-size trucks, about why the clean-sheet IRS cost "multimillions of dollars."  First, GM would need to build a new body shop at the Arlington, Texas plant that assembles the automaker's big SUVs to stamp the numerous wholly new parts and panels accommodating an IRS. Then GM would need to design and pay for a new assembly process. On top of those up-front costs, there was the incremental cost of the four-link IRS components being more expensive than those in the trucks' former leaf-sprung solid axles. Herrick endured so many rejections for so long that he remembers the date and time when he got approval for the new unit. He said it came down to a meeting where he told a higher-up, "I'll make you a deal: If we get to the reveal, or if we launch this and you think this was a dumb idea, I'll hand you my badge and let you walk me out." Head to Motor Trend to read the full story. Based on Herrick being on stage to help present the new SUVs to the press, and on our First Ride in the new Chevrolet Tahoe and Suburban at GM's Milford Proving Grounds, it appears this will have a happy ending for all involved. Furthermore, since Herrick worked on the T1 platform that supports the big SUVs as well as the light- and heavy-duty pickups, he understood the demands on the commercial side, too. That could be why when Roadshow asked Tim Asoklis, chief engineer of the Tahoe and Suburban, if the new IRS could endure life in the Chevrolet Silverado and GMC Sierra, Asoklis answered, "Oh, absolutely." Related Video: