1982 Chevrolet S-10 on 2040-cars

Auto blog

Here's the production Chevy Bolt

"It looks like a Volt had an evening of regrets with an i3." That's AutoblogGreen editor-in-chief Sebastian Blanco talking about the car you see here, the 2017 Chevy Bolt. Our trusty spy photographers caught the new Bolt EV fully uncovered at a photo shoot, ahead of its official debut at the Consumer Electronics Show in January. To say the styling looks familiar would be an understatement. There's a lot of Volt elements here, and the nod to the BMW i3 is definitely valid. It's not unattractive, it's just sort of, well, there. Never mind, the Bolt will have a lot going for it when it launches, should earlier rumors come to fruition. The hatchback is expected to have a 200-mile electric range, and should cost right around $30,000 after incentives. The Bolt will be built in Michigan, and will likely arrive at dealers in early 2017. Chevy knows this one's going to be huge, and the company is fully committed to launching and marketing the Bolt the right way. We'll have the full details in January at CES. For now, feast your eyes on His Boltness in the gallery above. Let us know what you think about it, in the Comments.

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Next Chevy Silverado could get this built-in tailgate step

General Motors just received patent approval for a tailgate step in a pickup bed. And given the timing, don't be surprised if you see this on the upcoming 2019 Silverado pickup (not the mention its GMC Sierra twin), expected to arrive in late 2018. According to the patent, granted in December of last year, the whole mechanism is housed in the tailgate assemble. The magic happens when a portion of the top half of the tailgate swings down and a step folds out. There's also a handle that locks into position to help climb up into the bed. As trucks get bigger and taller over the years, it gets harder and harder to access the cargo bed. Ford's solution with the 2009 F-150 was a step that slides out from the end of the tailgate. Back then, Chevy made an ill-advised ad highlighting the feature for Ford. And while Howie Long mocked the F-150's "man step" Ford saw almost a third of its trucks with the option in the first year. The GM design seems to improve on Ford's idea as it appears to be wider and has a back to the lower step. That is, you don't have to worry about stepping through the ladder-rung design as on the F-150. Ford's tailgate step later spread to the F Super Duty, and other cargo access assists have proliferated through the truck world. On the most recent redesign, the Chevrolet Silverado took a trick from the Avalanche and added cutouts to the corners of the rear bumper that act as a foothold. Ford also offers a deployable side step, Chevrolet has running boards that scoot rearward with a kick of the boot, and Ram offers fixed wheel-to-wheel side rails. Nissan is in on the game too, with an optional folding step that tucks under the rear bumper. We don't expect Chevrolet to comment on when or if we'll see this feature in the showrooms. But given that engineers are already hard at work on the next Silverado and the timing of this patent lines right up with the new truck's development cycle, we'll be disappointed if this patent stays in the file cabinet. Related Video: