1973 Chevrolet Nova Custom Hatchback 2-door Supercharged 357ci 755 Hp on 2040-cars

Auto blog

Race Recap: Rolex 24 at Daytona was fast and feisty

Let the record show that victory at the 2015 Rolex 24 at Daytona went to the No. 02 Chip Ganassi Racing with Felix Sabates Target/Ford EcoBoost Riley DP driven by Verizon IndyCar drivers Scott Dixon and Tony Kanaan and NASCAR drivers Jamie McMurray and Kyle Larson. The winner did 740 laps to cover 2,634.3 miles in 24 hours and 57.667 seconds. That's a statement to this year's pace in spite of 18 cautions, two more than last year: the Michael Shank Racing Ligier got pole with a time of 1:39.194, slower than last year's pole time of 1:38.270; however, the winning car last year only did 695 laps. The fight for top honors was shaved to a four-car battle over the first third of the event. The No. 02 Ganassi car took the lead on the first lap, swapping it well into the night with the No. 01 Ganassi car, the No. 10 Wayne Taylor Racing Corvette DP, and the defending champion No. 5 Action Express Corvette DP, all of them staying within about 20 seconds of one another. The Action Express car had a fuel connector come loose and lost three laps getting towed back to the pits to have it reattached, but was back in the lead 18 hours in. The No. 01 Ganassi car dropped out with recurring clutch problems 22 hours in, retiring not long after. A race-within-the-race is where the concluding action happened, a seven minute, 30-second dash from the end of the last caution to the checkered flag. During the penultimate pit stops with an hour to go, Dixon was in second place followed Jordan Taylor in the Wayne Taylor Racing DP into the pits but beat him out, taking the lead. The Action Express car was in third. In the last pit stops of the race, Dixon gained even more time, getting a four-second advantage over Taylor. Then a full-course caution came out twenty minutes before the finish when a Prototype Challenge car hit the wall and caught fire, bunching up the field. That closed the pits, but the Wayne Taylor Racing car had to pit during that yellow because of a miscalculation of driver time. No driver can be behind the wheel for more than four hours in a six-hour period but Jordan Taylor was going to go over, so he came in to swap out for brother Ricky. That cost the team any chance of second place, since they took an additional drive-through penalty for entering closed pits. When the track went green again, Sebastien Bourdais in the Action Express car stayed all over Dixon for the final five laps but couldn't get around him.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Someone has already test driven the 2016 Chevy Volt

Due to some well-placed connections at General Motors Canada headquarters in Oshawa, a senior member of the gm-volt.com forum with the handle "kickincanada" got about 30 minutes behind the wheel of a 2016 Chevrolet Volt. Kickincanada owns a 2012 Volt, and other than personal reservations over the styling of the new car, he came way nothing but impressed by the second-generation hybrid. He drove the Premier trim, posted his observations on the site, then answered questions for other owners desperate to find out what's coming. He said the interior materials are "more upscale," there is less hard plastic and better leather, the seats are more comfortable, and ergonomically, "Everything is beautifully laid out." Although obviously not as luxurious, the interior reminded him of the Cadillac ELR. Tech touches like a better display, Apple integration, a wireless charging area for the phone, heated rear seats, and a better rear console were also worth noting. As for driving, Kickincanada called it "incredible." The "much more luxurious drive" comes courtesy of a "firm and sporty" suspension setup, less NVH thanks to more sound insulation, quieter Michelin Energy Saver tires, and quieter operation of the genset ICE. He said acceleration from a standstill felt quicker because there was no delay between applying the throttle and the car taking off. He estimates owners should be able to get about 100 kilometers (62 miles) out of the electric mode alone on a full charge, and that the new Volt is "clearly improved in almost every way" (the car's official range, as determined by the EPA, is 53 electric miles). We look forward to finding out ourselves. Click through to gm-volt to read all of his thoughts and responses if there's a hybrid purchase in your future. Related Video: